Just as the title says, I'm installing a new master cylinder on my 73 and the new one has a different plug in for the electrical line then the old one. Tell me what you guys did.
The old one looks damaged. The new one is correct. What does the wire connector look like? The wire should have a spade connector on it.
70-73 has 2 spade connector. 74-76 has single pole. I think you can leave the brown wire off and tape it back and it will still work. If not I have some NOS 2 pole switches.
Ill check it out tomorrow and let you guys know. Thanks
The switch did not occur at any specific point that I know of, but we do see both two-connector and one-connector switches.
The two-connector switches short the two connectors together when a pressure imbalance is detected. One connector goes to the brake warning light, and the other goes to brown through the standard brown wire.
The one-connector switch grounds through its threads into the body of the master cylinder. If you have a one-connector switch, just tape the ground wire up out of the way.
--DD
My '75 has spade lug connectors, but there were so many things that weren't 'original' on the car when I acquired it. I'd just crimp on a new spade lug and be done with it - All new M/Cs I've seen come with sensors that have the spade connection anyway.
Also, make sure to completely seat the plastic feed nipples (or whatever they're called) into the rubber grommets on the M/C. Some folks like to disconnect the feed lines from the reservoir and pull them downward a little so the nipples are easier to install (before bolting the M/C to the bulkhead), then pull the lines back up and reconnect to the reservoir
I think you're due for a new one ... and from the looks of the surrounding areas, a whole new M/C. It looks like maybe you're doing that now?
Yup got a brand new m/c shown in a pic above. Anyone have any extra connectors?
It looks like your old switch broke in half when you removed it. Just pull the spade connectors off the broken half of your old switch that's dangling there. Tape the brown wire back, and plug the other wire into the new switch, as Dave mentioned above.
Know what the part number is by chance?
Did the spade connector come off of the broken part of the switch? It looks from your pic that the spade connector is still connected to the broken part and still on the wire. You may not need to buy a spade connector. Best to use the existing spade if still attached and not hack into the wiring if possible.
It looks like one broke wire off, and with all the rust I see in the boot, the wire to spade connections probably have a lot of corrosion anyway.
Lowe's has them http://www.lowes.com/pd_136071-12704-770302_1z0yt4o__?productId=3130409&pl=1
Harbor Freight is another place to get them ... and they sell a crimp tool for $4.
Thanks for the input guys, can someone show me what its spose to look like so i have a better understanding. The switch that is
Here is the new switch you PM me about. $20 shipped Priority Mail. Your remove the old two pole broken cap. Clean the ends of the wires with lemon juice and salt solution. It cleans the brass ends up nice.
Attached image(s)
Sorry for sounding like a dumbass but im confused as to where that switch screws into? Thought that plug in just plugs right into that port of the new master cylinder?
Where the single pole one is now.
So take out that single pole on the new master cylinder and put that double pole in?
Yes
Ok thanks for clearing that up haha, next question will i need a new end that plugs into that 2 pole switch?
See my previous post (post# 18) http://www.914world.com/bbs2/index.php?s=&showtopic=263202&view=findpost&p=2230789
Thanks euro, payment sent your way sixer check your messages
Got it now. I'm a visual person when it comes to working on cars that's why I asked so many questions. I wasn't sure what a unbroken one looks like so you see where I was coming from. Thanks for all the info tho guys. Big help
Going out in the morning. I worked out of town today.
Awesome, appreciate it
Also, make sure to install a new copper washer when installing the new switch.
It's a good idea to 'bench bleed' the M/C before installing it in the car too.
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)