What I did today, Removed tar from interior floorboards |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
What I did today, Removed tar from interior floorboards |
watsonrx13 |
Nov 21 2004, 06:02 PM
Post
#1
|
Advanced Member Group: Members Posts: 2,735 Joined: 18-February 03 From: Plant City, FL Member No.: 312 Region Association: South East States |
Well it was a perfect day in sunny Florida (finally) so I decided to get some work done on the teener. Today the objective was to remove the tar from the interior floorboards.
Here's the before pic: 1 of 4 Attached image(s) |
watsonrx13 |
Nov 21 2004, 06:03 PM
Post
#2
|
Advanced Member Group: Members Posts: 2,735 Joined: 18-February 03 From: Plant City, FL Member No.: 312 Region Association: South East States |
I used an air-hammer and a short chisel. It took me about 3 hours to completely remove the tar. Here's a shot after 30 min removing the tar from underneat the passenger's seat.
2 of 4 Attached image(s) |
watsonrx13 |
Nov 21 2004, 06:04 PM
Post
#3
|
Advanced Member Group: Members Posts: 2,735 Joined: 18-February 03 From: Plant City, FL Member No.: 312 Region Association: South East States |
Next I needed to remove the seam-sealer and the residual tar. I used an angle-grinder with a huge wire-wheel (I completely wore the wire wheel out and will need to replace it). I also used several screw-drivers to remove the seam-sealer in the tight corners.
3 of 4 Attached image(s) |
watsonrx13 |
Nov 21 2004, 06:04 PM
Post
#4
|
Advanced Member Group: Members Posts: 2,735 Joined: 18-February 03 From: Plant City, FL Member No.: 312 Region Association: South East States |
Finally, I cleaned the floor and covered it with Ospho to protect it until I can paint. I still have the pedal area floorboard to finish cleaning, along with center tunnel.
Not bad for 8 hrs work. 4 of 4 Attached image(s) |
Series9 |
Nov 21 2004, 06:09 PM
Post
#5
|
Lesbians taste like chicken. Group: Members Posts: 5,444 Joined: 22-August 04 From: DeLand, FL Member No.: 2,602 Region Association: South East States |
If you use a propane torch and a putty knife, that tar comes up a little easier.
|
Jeroen |
Nov 21 2004, 06:31 PM
Post
#6
|
914 Guru Group: Members Posts: 7,887 Joined: 24-December 02 From: The Netherlands Member No.: 3 Region Association: Europe |
nice job!
looks like there are no new nasty surprises |
watsonrx13 |
Nov 21 2004, 06:39 PM
Post
#7
|
Advanced Member Group: Members Posts: 2,735 Joined: 18-February 03 From: Plant City, FL Member No.: 312 Region Association: South East States |
No, it was very clean, but since I was in there...
Once I finish with the interior, I'm going back over the engine compartment and rear trunk to check anything I might have missed. Then I'm going to paint these areas, looking at end of Dec/early Jan. Anyway, that's the plan for now (subject to change without prior notification... (IMG:style_emoticons/default/wacko.gif) ) |
Lo-Fi Version | Time is now: 27th September 2024 - 01:21 PM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |