brain cramp help, carb confusion! |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
brain cramp help, carb confusion! |
iankarr |
May 8 2016, 08:26 AM
Post
#1
|
The wrencher formerly known as Cuddy_K Group: Members Posts: 2,512 Joined: 22-May 15 From: Heber City, UT Member No.: 18,749 Region Association: Intermountain Region |
Hi Guys,
This is going to be the stupidest question I've ever posted, but I'm sure it will get the quickest answer... When adjusting the idle mixture screws on a Weber, does screwing in = leaner, or out? I don't know why I can't wrap my head around this...or find a simple answer online. The short bus is stopped outside my house. |
rhodyguy |
May 8 2016, 08:38 AM
Post
#2
|
Chimp Sanctuary NW. Check it out. Group: Members Posts: 22,188 Joined: 2-March 03 From: Orion's Bell. The BELL! Member No.: 378 Region Association: Galt's Gulch |
Turning the screw in shuts off the fuel for that idle circuit. As the cyl goes lean you'll hear it and prob note a stumble.
|
iankarr |
May 8 2016, 08:58 AM
Post
#3
|
The wrencher formerly known as Cuddy_K Group: Members Posts: 2,512 Joined: 22-May 15 From: Heber City, UT Member No.: 18,749 Region Association: Intermountain Region |
Thanks!
So....in=lean, out=rich? |
rhodyguy |
May 8 2016, 09:07 AM
Post
#4
|
Chimp Sanctuary NW. Check it out. Group: Members Posts: 22,188 Joined: 2-March 03 From: Orion's Bell. The BELL! Member No.: 378 Region Association: Galt's Gulch |
Yes. Only gently seated when turning in. DON'T reef on it. Examine the needle tip. A grove can form from excessive pressure. Refer to the CB weber book. It's a great asset for understanding how the webers work and setting them up.
|
porschetub |
May 8 2016, 03:08 PM
Post
#5
|
Advanced Member Group: Members Posts: 4,725 Joined: 25-July 15 From: New Zealand Member No.: 18,995 Region Association: None |
From memory its around 2 and one half turns out,if your idle jets are in the ballpark that is.
I have found in the past if the idle jets are wrong the mixture screws don't respond to adjustment as well or you could have a vacuum leak. |
Darren C |
May 8 2016, 03:26 PM
Post
#6
|
Member Group: Members Posts: 392 Joined: 26-December 14 From: Chichester UK Member No.: 18,255 Region Association: England |
2 1/2 out will get you up and running but it'll be too rich, so dont leave them there too long.
As Rhody guy says, wind them in maybe 1/4 turn each (all at the same time initially from the 2 1/2 starting point and see if it still runs ok (should do) Then turn in each slowly (individually) until you hear the cylinder "drop out", then back out maybe 1/8 turn from drop out or until that cylinder fires smoothly. You can get it pretty good using this method, but to be most accurate you'll need a gas analyser to get the CO at between 2.5 & 3%. Another easy check is go for a ride and see what color the tail pipe is. Black= Too Rich. White= Too lean. Mid Gray is good |
iankarr |
May 8 2016, 07:37 PM
Post
#7
|
The wrencher formerly known as Cuddy_K Group: Members Posts: 2,512 Joined: 22-May 15 From: Heber City, UT Member No.: 18,749 Region Association: Intermountain Region |
Thanks Guys. I got it running pretty well. Carbs balanced and the new Tangerine Racing linkage is huge. Almost done and ready for the summer.
|
stugray |
May 8 2016, 08:18 PM
Post
#8
|
Advanced Member Group: Members Posts: 3,825 Joined: 17-September 09 From: Longmont, CO Member No.: 10,819 Region Association: None |
|
Lo-Fi Version | Time is now: 27th September 2024 - 01:35 PM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |