Retorque 2.0 heads? Pro and Cons? |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
Retorque 2.0 heads? Pro and Cons? |
914rrr |
Mar 27 2009, 11:36 AM
Post
#1
|
Senior Member Group: Members Posts: 1,835 Joined: 1-July 03 From: Knoxville, TN Member No.: 874 Region Association: South East States |
I am in the process of freshening and detailing my 2.0 engine. While I have the engine sheet metal off, is it a good idea to retorque the heads? Are there any pros or cons to doing this?
Rob |
type47 |
Mar 27 2009, 02:02 PM
Post
#2
|
Viermeister Group: Members Posts: 4,254 Joined: 7-August 03 From: Vienna, VA Member No.: 994 Region Association: MidAtlantic Region |
Engine is out of the car? I would think there is no harm in retorquing, I guess, theoretically, if the engine hasn't been run, that the torque should be the same as when done before. I would expect the torque to perhaps be different after the motor has gone through some heat cycles but it would be a real pain to retorque the heads then with the motor in since the upper head nuts would be hidden by the engine sheet metal.
|
So.Cal.914 |
Mar 27 2009, 02:55 PM
Post
#3
|
"...And it has a front trunk too." Group: Members Posts: 6,588 Joined: 15-February 04 From: Low Desert, CA./ Hills of N.J. Member No.: 1,658 Region Association: None |
If it's out why not check the torque on them. Follow the torque pattern in your manual. (IMG:style_emoticons/default/smile.gif)
|
yeahmag |
Mar 27 2009, 05:32 PM
Post
#4
|
Advanced Member Group: Members Posts: 2,435 Joined: 18-April 05 From: Pasadena, CA Member No.: 3,946 Region Association: Southern California |
I typically only do this when the motor is brand spanking new. You get a "carbon" seal around the chamber and run the risk of upsetting that. I could be insane though...
|
charliew |
Mar 27 2009, 11:39 PM
Post
#5
|
Advanced Member Group: Members Posts: 2,363 Joined: 31-July 07 From: Crawford, TX. Member No.: 7,958 |
I took a 72 bug away from my son in 1986 because he kept drinking too much. He asked for it back last june. He's now 40. It has about 50 k on the original motor. We repainted all the tin, replaced the clutch and pressure plate and bearing so decided to do the seal and check the endplay. It was ok. I had a 009 dist on it in 86 but decided to try a vaccum advance one this time.
I also put a new oilpump/filter on it with new pushrod tubes. While we were at it we checked the head torque and it was pretty loose. More than I expected it to be. We had driven the car before we tore it apart to redo it and it ran ok. |
yeahmag |
Mar 27 2009, 11:43 PM
Post
#6
|
Advanced Member Group: Members Posts: 2,435 Joined: 18-April 05 From: Pasadena, CA Member No.: 3,946 Region Association: Southern California |
Might check for the head studs pulling out. Type I cases have been known for that. I personally haven't run across one that needed re-torqued without a reason, but I have a fairly limited cross section...
|
sean_v8_914 |
Mar 28 2009, 12:02 AM
Post
#7
|
Chingon 601 Group: Members Posts: 4,011 Joined: 1-February 05 From: San Diego Member No.: 3,541 |
you can not retorque rusty nuts on rusty stud. you can only try.
if it aint broke... |
LvSteveH |
Mar 28 2009, 04:07 PM
Post
#8
|
I put the Poor in Porsche Group: Members Posts: 1,080 Joined: 22-April 03 From: Las Vegas, Nevada Member No.: 600 |
I broke a stud in an othewise healthy 3.6L a few years ago because I retorqued the head studs instead of just checking that they weren't broken. Only cost me about $3000 (IMG:style_emoticons/default/biggrin.gif)
Kind of a freak thing really. As long as everything is clean with no corrosion issues I wouldn't be afraid to check them. |
Lo-Fi Version | Time is now: 27th September 2024 - 11:56 AM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |