 Got a tubing bender I can borrow?, In or around San Jose |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| jonwatts |
 Feb 9 2006, 10:01 AM
Post
#1
|
|
no rules, just wrong  Group: Benefactors Posts: 2,321 Joined: 13-January 03 From: San Jose, CA Member No.: 141   |
I need to bend some 1.5" thin wall Al tube (not structural, obviously). Conduit benders don't come that big. I think a Harbor Freight pipe bender would be fine for the job. Anybody local have one I can borry? If not I may pick one up (they're even on sale at the moment).
(IMG:http://www.harborfreight.com/cpi/photos/32800-32899/32888.gif) |
   |
 
|
  |
Replies
| charliew |
Mar 27 2009, 09:45 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 2,363 Joined: 31-July 07 From: Crawford, TX. Member No.: 7,958 |
Wilhelm I hate to say it but I haven't tried the speedway bender yet but I think I saw almost the same bender somewhere else cheaper. In the speedway instructions it says to use a lubricant to keep from galling the wall of the tube.
|
|
|
|
Posts in this topic
jonwatts Got a tubing bender I can borrow? Feb 9 2006, 10:01 AM
TimT That type bender wont cut it, you'll end up ki... Feb 9 2006, 10:29 AM jonwatts I've heard these aren't very good, don... Feb 9 2006, 10:45 AM TimT The bender in the link you posted has a die that s... Feb 9 2006, 10:57 AM TimT oops it $399 now, Speedway Feb 9 2006, 10:59 AM jonwatts Do you mean this die? Feb 9 2006, 11:09 AM jonwatts Sorry, lousy image. Do you mean the big die or the... Feb 9 2006, 11:12 AM neo914-6 Jon,
Contact Sonu (914 1.8t ), we were just talki... Feb 9 2006, 11:15 AM 1bad914 The one you have pictured from HF will work, but y... Feb 9 2006, 11:23 AM jonwatts I don't know if I've ever talked to Sonu. ... Feb 9 2006, 11:52 AM Mueller not sure what you are trying to do, but you could ... Feb 9 2006, 01:51 PM jonwatts Feb 9 2006, 02:56 PM neo914-6 I'm building a heat shield bra <... Feb 9 2006, 06:19 PM charliew I bought a hf PIPE bender. It works on pipe. A tub... Mar 25 2009, 11:09 PM Wilhelm If you only need a few bends heres a lower cost co... Mar 26 2009, 11:47 PM kwales Pack the tubing with sand, close the ends and bend... Mar 27 2009, 12:48 PM underthetire Know any electricians? We have a hyraulic greenli... Mar 27 2009, 01:06 PM
|
3 User(s) are reading this topic (3 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 23rd November 2024 - 07:06 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.