Head Gaskets |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
Head Gaskets |
brandomc |
Sep 16 2009, 04:48 PM
Post
#1
|
Member Group: Members Posts: 113 Joined: 14-May 09 From: los angeles california Member No.: 10,363 Region Association: Southern California |
I bought a engine last week that was supposedly a 1.7, but the guy didnt really know for sure. After looking at the case numbers, I think it might be a 1.8?? It starts with EB. I took all of the sheetmetal off to repaint it, and everything is really clean accept for around 1 of the cylinders between the head and the cylinder, it is black and kindof oily. I figure this is a leaky cylinder. Do i need new head gaskets? Or just retorque the head? Where do i get head gaskets? Pelican parts doesnt sell them. What should i do with this? It is supposed to be a fairly low mileage engine. Thanks
|
aircooledtechguy |
Sep 16 2009, 05:13 PM
Post
#2
|
The Aircooledtech Guy Group: Members Posts: 1,966 Joined: 8-November 08 From: Anacortes, WA Member No.: 9,730 Region Association: Pacific Northwest |
I would pull the head and see if there is a gasket in there that is getting sucked inward. If there is remove it AND the other three from the other cylinders. Check that head for erosion at the leaking point. These leaks when caught early are no problem to correct. Over time the leak acts like a cutting torch to totally destroy the head and piston.
These gaskets PROMOTE leaks and should NOT be used. |
brandomc |
Sep 16 2009, 05:21 PM
Post
#3
|
Member Group: Members Posts: 113 Joined: 14-May 09 From: los angeles california Member No.: 10,363 Region Association: Southern California |
I would pull the head and see if there is a gasket in there that is getting sucked inward. If there is remove it AND the other three from the other cylinders. Check that head for erosion at the leaking point. These leaks when caught early are no problem to correct. Over time the leak acts like a cutting torch to totally destroy the head and piston. These gaskets PROMOTE leaks and should NOT be used. Thanks for the info, that sounds like a good solution. Does everybody else agree? Is removing that gasket going to bump up my compression ratio at all? Just currious. What can i do if ther is some surface erosion? Is everything going to bolt right back on, or do i need any other seals or caskets when i go through this? Thanks again |
Cap'n Krusty |
Sep 16 2009, 06:27 PM
Post
#4
|
Cap'n Krusty Group: Members Posts: 10,794 Joined: 24-June 04 From: Santa Maria, CA Member No.: 2,246 Region Association: Central California |
I would pull the head and see if there is a gasket in there that is getting sucked inward. If there is remove it AND the other three from the other cylinders. Check that head for erosion at the leaking point. These leaks when caught early are no problem to correct. Over time the leak acts like a cutting torch to totally destroy the head and piston. These gaskets PROMOTE leaks and should NOT be used. Thanks for the info, that sounds like a good solution. Does everybody else agree? Is removing that gasket going to bump up my compression ratio at all? Just curious. What can i do if there is some surface erosion? Is everything going to bolt right back on, or do i need any other seals or gaskets when i go through this? Thanks again I DO NOT agree. 36 Years of T4 experience, all of it professionally, tells me you need to use/keep the head gaskets on a stockish 1.7. If you choose to delete them, be sure to calculate and shim the cylinders to make up for the increased compression, something you DO NOT want, especially with the fuel we get today...... If you have erosion on either the cylinders or the heads, you'll need to replace the pistons and cylinders or surface the heads, which ever is appropriate, and shim the cylinders to compensate for the material removed. DO NOT lap the cylinders into the heads. Your eyes and arms DO NOT constitute a vertical milling machine, and they're not gonna maintain the tolerances. You will need head gaskets, pushrod tube gaskets, exhaust gaskets, valve cover gaskets, and intake insulator/gaskets. The Cap'n |
Lo-Fi Version | Time is now: 27th September 2024 - 02:08 PM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |