 Fiberglass flare installation- Rivet on! |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Trekkor |
 Nov 2 2012, 12:42 PM
Post
#1
|
|
I do things...  Group: Members Posts: 7,809 Joined: 2-December 03 From: Napa, Ca Member No.: 1,413 Region Association: Northern California  |
Wanting more tire, the time finally came to go wider body.
Here, you can see how easy and fast you can produce a good looking flare install. I started with professionally painted flares and plastic edge molding. Measure and mark the car carefully before cutting: (IMG:http://www.914world.com/bbs2/uploads_offsite/i944.photobucket.com-1413-1351881777.1.jpg) (IMG:http://www.914world.com/bbs2/uploads_offsite/i944.photobucket.com-1413-1351881777.2.jpg) (IMG:http://www.914world.com/bbs2/uploads_offsite/i944.photobucket.com-1413-1351881778.3.jpg) After holding/clamping the flares in their finished position, trace a light pencil line along the outside edge of the flare onto the car. Apply 2" masking tape to the line. The inside edge of the tape becomes your cut line: (IMG:style_emoticons/default/sawzall-smiley.gif) (IMG:http://www.914world.com/bbs2/uploads_offsite/i944.photobucket.com-1413-1351881778.4.jpg) (IMG:http://www.914world.com/bbs2/uploads_offsite/i944.photobucket.com-1413-1351881778.5.jpg) KT |
   |
 
|
  |
Replies
| Trekkor |
Nov 2 2012, 01:46 PM
Post
#2
|
|
I do things... Group: Members Posts: 7,809 Joined: 2-December 03 From: Napa, Ca Member No.: 1,413 Region Association: Northern California |
QUOTE I have grown to really like the look. Me too. Nice look with the two tone. Thanks for the post. KT |
|
|
|
Posts in this topic
Trekkor Fiberglass flare installation- Rivet on! Nov 2 2012, 12:42 PM
Trekkor I used both the sawzall and a jigsaw with a metal ... Nov 2 2012, 12:45 PM Trekkor Takes a bit of courage and confidence to hack into... Nov 2 2012, 12:50 PM Trekkor Run the molding over the flare edges, leaving them... Nov 2 2012, 12:56 PM
Dasnowman
Run the molding over the flare edges, leaving the... Nov 4 2012, 02:53 AM
Woody
Run the molding over the flare edges, leaving th... Nov 4 2012, 09:38 AM Randal
Run the molding over the flare edges, leaving the... Dec 1 2012, 10:42 AM Trekkor Take your time, double check before any cutting or... Nov 2 2012, 12:58 PM Trekkor After you are done, trim the excess molding with a... Nov 2 2012, 01:04 PM Trekkor This is how much rear tire I gained!!
11... Nov 2 2012, 01:11 PM Woody
I have grown to really like the look. Nov 2 2012, 01:40 PM 396
I have grown to really like the look.
W... Dec 3 2012, 06:41 AM Woody
I have grown to really like the look.
... Dec 3 2012, 01:55 PM Woody No problem buddy and thanks. I borrowed the look f... Nov 2 2012, 01:59 PM gothspeed Ahhhh wonderful flares ............. :D
Hey woo... Nov 2 2012, 03:17 PM Woody
Ahhhh wonderful flares ............. :D
Hey wo... Nov 2 2012, 03:27 PM gothspeed
Stacked 25mm on each wheel with the cookie cutter... Nov 2 2012, 03:34 PM Trekkor I found a few more pics:
http://www.914world.com/... Nov 3 2012, 08:54 PM Krieger Dang KT those look good! Where were you when ... Nov 4 2012, 09:35 AM aircooledtechguy I actually prefer the riveted/bolted-on look and r... Nov 4 2012, 09:44 AM Trekkor FYI:
The source of my tires!
http://www.914wo... Nov 29 2012, 03:31 PM Jeff Hail I think you need to flare that open wheeled chair ... Nov 29 2012, 06:03 PM The Metal Surgeon
I think you need to flare that open wheeled chair... Nov 30 2012, 01:07 AM Bartlett 914
I think you need to flare that open wheeled chai... Nov 30 2012, 08:41 AM Chris H.
I think you need to flare that open wheeled chai... Nov 30 2012, 03:38 PM Dasnowman
It's nice but I will be in for a couple hun... Nov 30 2012, 05:01 PM Dasnowman I'm exceited got an email saying me flares are... Nov 29 2012, 10:21 PM cary DrChapman (Gary) has them on his 6. I think they l... Nov 29 2012, 11:15 PM Trekkor My side markers were welded up before I had the ca... Nov 29 2012, 11:34 PM pete-stevers hope you where careful around the oil tank.... bri... Nov 30 2012, 11:10 AM yeahmag I'm so tempted to do this myself... I'm al... Nov 30 2012, 12:25 PM Vacca Rabite This thread is not about welding. There are dozen... Nov 30 2012, 12:51 PM Dasnowman
This thread is not about welding. There are doze... Nov 30 2012, 01:59 PM Trekkor We need to do that three flared car a/x reunion ne... Dec 1 2012, 01:21 PM Randal
We need to do that three flared car a/x reunion n... Dec 2 2012, 06:34 PM Trekkor
What help? :confused:
You were my first a/x... Dec 2 2012, 07:35 PM bulitt Ex Crackers Flares-
http://www.914world.com/bbs2/... Dec 3 2012, 06:09 AM SirAndy
Ex Crackers Flares-
http://www.914world.com/bbs2... Dec 3 2012, 02:23 PM SirAndy :idea: :idea: :smash: :welder: :woohoo:
Quic... Dec 3 2012, 03:39 PM waltonsm To revive an old thread....
What flares/rockers a... Nov 30 2016, 01:29 AM DBCooper I like that riveted look. Says "Yeah, that... Dec 3 2012, 01:34 PM Rand You anodized it! Nice! ;p
I like it. One ... Dec 3 2012, 03:44 PM bshounen lov'n the fenders, i would like to see some ol... Apr 16 2014, 08:59 PM CptTripps I'll be riveting my next flares like this. The... Apr 16 2014, 09:23 PM |
18 User(s) are reading this topic (18 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 23rd November 2024 - 01:43 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.