Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

2 Pages V  1 2 >  
 Reply to this topicStart new topic
> Steel Flares installed, I have only had them a year now...ahead of schedule
kfish914
post Nov 29 2011, 04:12 PM
Post #1


Member
**

Group: Members
Posts: 161
Joined: 7-May 08
From: Osceola, Indiana
Member No.: 9,026
Region Association: Upper MidWest
I finally got my flares welded over the Turkey weekend

marking the panels
Attached ImageAttached Image

the cut out
Attached Image

the weld
Attached Image

all welded up
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
tscrihfield
post Nov 29 2011, 04:13 PM
Post #2


Drive Fast and Take Chances
***

Group: Members
Posts: 643
Joined: 8-September 10
From: Amelia Ohio
Member No.: 12,156
Region Association: None
Nice! Looks good!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
TurbOH Brad
post Nov 29 2011, 04:23 PM
Post #3


Brad. Just Brad.
**

Group: Members
Posts: 207
Joined: 2-February 11
From: Sparks, NV
Member No.: 12,654
Region Association: Northern California
I take it you are deleting the front side marker?

The factory M471 GT's that were imported still had them, but I believe they were moved farther forward on the fender, or perhaps the flares were welded further back.

Either way, it looks good.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BajaXJ92
post Nov 29 2011, 05:10 PM
Post #4


Extended Member
****

Group: Members
Posts: 2,146
Joined: 20-April 06
From: Prescott, AZ
Member No.: 5,895
Region Association: MidAtlantic Region
Awesome! (IMG:style_emoticons/default/beerchug.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bulitt
post Nov 29 2011, 05:35 PM
Post #5


Achtzylinder
****

Group: Members
Posts: 4,188
Joined: 2-October 11
Member No.: 13,632
Region Association: South East States
Did you butt weld or lap?
Did mine last week also, found lots of bondo and had fitment issues on left rear.
Looks good!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
McMark
post Nov 29 2011, 06:55 PM
Post #6


914 Freak!
***************

Group: Retired Admin
Posts: 20,179
Joined: 13-March 03
From: Grand Rapids, MI
Member No.: 419
Region Association: None
Please tell me you didn't leave that flap of metal in there. (IMG:style_emoticons/default/yikes.gif)

If so, get your head up in there with a grinder and get it out. Overlapping panels like that will capture water and lead to rusted out fenders. Seam sealer will only work as a band-aid. Once the seam sealer breaks down, it traps water BETTER!

Otherwise, nice work! (IMG:style_emoticons/default/cool_shades.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
rick 918-S
post Nov 29 2011, 08:16 PM
Post #7


Hey nice rack! -Celette
***************

Group: Members
Posts: 20,783
Joined: 30-December 02
From: Now in Superior WI
Member No.: 43
Region Association: Northstar Region
QUOTE(McMark @ Nov 29 2011, 06:55 PM) *

Please tell me you didn't leave that flap of metal in there. (IMG:style_emoticons/default/yikes.gif)

If so, get your head up in there with a grinder and get it out. Overlapping panels like that will capture water and lead to rusted out fenders. Seam sealer will only work as a band-aid. Once the seam sealer breaks down, it traps water BETTER!

Otherwise, nice work! (IMG:style_emoticons/default/cool_shades.gif)


(IMG:style_emoticons/default/agree.gif) It's ok to use the overlap method for welding only. This will help with heat warpage. Once your finished get in there and remove the strip of metal, grind everything nicely, use a light on the inside and check for pin holes.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Socalandy
post Nov 30 2011, 12:25 AM
Post #8


Its got to be Yellow!!!
****

Group: Members
Posts: 2,432
Joined: 29-August 09
From: Orange
Member No.: 10,742
Region Association: Southern California
very nice, I cant wait to get mine on
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bulitt
post Nov 30 2011, 07:07 AM
Post #9


Achtzylinder
****

Group: Members
Posts: 4,188
Joined: 2-October 11
Member No.: 13,632
Region Association: South East States
QUOTE(McMark @ Nov 29 2011, 07:55 PM) *

Please tell me you didn't leave that flap of metal in there. (IMG:style_emoticons/default/yikes.gif)

If so, get your head up in there with a grinder and get it out. Overlapping panels like that will capture water and lead to rusted out fenders. Seam sealer will only work as a band-aid. Once the seam sealer breaks down, it traps water BETTER!

Otherwise, nice work! (IMG:style_emoticons/default/cool_shades.gif)


Whats the best way to seal the welds on the inner side?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
scotty b
post Nov 30 2011, 07:20 AM
Post #10


rust free you say ?
***************

Group: Members
Posts: 16,375
Joined: 7-January 05
From: richmond, Va.
Member No.: 3,419
Region Association: None
QUOTE(bulitt @ Nov 30 2011, 05:07 AM) *

QUOTE(McMark @ Nov 29 2011, 07:55 PM) *

Please tell me you didn't leave that flap of metal in there. (IMG:style_emoticons/default/yikes.gif)

If so, get your head up in there with a grinder and get it out. Overlapping panels like that will capture water and lead to rusted out fenders. Seam sealer will only work as a band-aid. Once the seam sealer breaks down, it traps water BETTER!

Otherwise, nice work! (IMG:style_emoticons/default/cool_shades.gif)


Whats the best way to seal the welds on the inner side?

I always grind them down smooth just like the outside, but if you opt to leave the bead, at least knock the tops off to level it and apply some primer ( etch then seal, or only use epoxy primer ) then a bead of seam sealer BRUSHED onto the weld. Simply laying a bead out of a caulk tube will leave voids and adhesion will be minimal. You can lay the bead but then follow it up with a small acid brush to get the sealer into the cracks and spread it out a bit. Followed that with a coat of primer and undercoating. All this CAN be done with reattle can products, but would be best with real 2 part paints and a gun.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
kfish914
post Nov 30 2011, 08:45 AM
Post #11


Member
**

Group: Members
Posts: 161
Joined: 7-May 08
From: Osceola, Indiana
Member No.: 9,026
Region Association: Upper MidWest
Yes, deleted the side marker lights. I had a lot of trouble deciding to remove them but after looking at a lot of pictures I did not like the look of them moved forward and like the cleaner look of the European cars. I may add a small side marker behind the front flares some day.

Yes, we did overlap weld cut out the ribbon of metal behind and ran a weld bead along the inside as well. We then coated with an epoxy primer and will spray with undercoating next. My friend who has done body work for 18 years believes this gives a stronger joint. Right or wrong he did most of the work so I went with his suggestion.

We had some fitment issues as well getting the bottoms to fit well. Otherwise the panels went on very well. Looking forward to all the sanding and filling and sanding to get everything baby smooth.
Thanks for your responses. Getting flares put on was a 20 year dream of mine. Now if I can figure out the wiring for the 2.7 six I should have this ready to drive in the spring, around here is mid April if we are lucky.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
JMKnight
post Nov 30 2011, 09:30 AM
Post #12


Aces & Eights
**

Group: Members
Posts: 135
Joined: 30-December 09
From: Northern Indiana
Member No.: 11,188
Region Association: Upper MidWest
(IMG:style_emoticons/default/aktion035.gif) REALLY NEET!, maybe I'll se you around the Bend next Summer!!. I'm driving a yellow 914 (IMG:style_emoticons/default/biggrin.gif)
QUOTE(kfish914 @ Nov 29 2011, 02:12 PM) *

I finally got my flares welded over the Turkey weekend

marking the panels
the cut out
the weld
all welded up
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
kfish914
post Nov 30 2011, 12:53 PM
Post #13


Member
**

Group: Members
Posts: 161
Joined: 7-May 08
From: Osceola, Indiana
Member No.: 9,026
Region Association: Upper MidWest
Yeah, I hope to see you also. I was the guy who drove over to pick up the t-shirt. If everything goes well I will be hitting some of the cruise ins in the area. My dad and I try and get out to the Das EssenHaus on their Thursday cruise ins starting in May.
For those that have not seen his yellow one it looks great in person.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
McMark
post Nov 30 2011, 04:30 PM
Post #14


914 Freak!
***************

Group: Retired Admin
Posts: 20,179
Joined: 13-March 03
From: Grand Rapids, MI
Member No.: 419
Region Association: None
Awesome! Definitely sounds like you found one of the good guys. (IMG:style_emoticons/default/thumb3d.gif)

Are they headed for paint?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
patssle
post Nov 30 2011, 08:59 PM
Post #15


Senior Member
***

Group: Members
Posts: 981
Joined: 28-August 09
From: Houston, TX
Member No.: 10,741
Region Association: None
Who's flares are those? And any pics of the rear on?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
sean_v8_914
post Dec 1 2011, 07:55 AM
Post #16


Chingon 601
****

Group: Members
Posts: 4,011
Joined: 1-February 05
From: San Diego
Member No.: 3,541
could you please show us a close up of the bottom joint near the rocker panel?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
pdlightning
post Dec 1 2011, 10:44 AM
Post #17


Member
**

Group: Members
Posts: 207
Joined: 4-February 11
From: Santa Clarita
Member No.: 12,660
Region Association: Southern California
QUOTE(sean_v8_914 @ Dec 1 2011, 05:55 AM) *

could you please show us a close up of the bottom joint near the rocker panel?


Very nice!

I would like to see those also. Are you using the wide body rockers for those flairs?

After completing these, would you overlap them again or butt weld considering all factors. I am still floundering on which way to do mine.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
mepstein
post Dec 1 2011, 11:23 AM
Post #18


914-6 GT in waiting
***************

Group: Members
Posts: 19,592
Joined: 19-September 09
From: Landenberg, PA/Wilmington, DE
Member No.: 10,825
Region Association: MidAtlantic Region
QUOTE(pdlightning @ Dec 1 2011, 11:44 AM) *

QUOTE(sean_v8_914 @ Dec 1 2011, 05:55 AM) *

could you please show us a close up of the bottom joint near the rocker panel?


Very nice!

I would like to see those also. Are you using the wide body rockers for those flairs?

After completing these, would you overlap them again or butt weld considering all factors. I am still floundering on which way to do mine.


Factory butt welded. So does Scotty B...(IMG:style_emoticons/default/smile.gif)

User is offlineProfile CardPM
Go to the top of the page
+Quote Post
kfish914
post Dec 1 2011, 09:39 PM
Post #19


Member
**

Group: Members
Posts: 161
Joined: 7-May 08
From: Osceola, Indiana
Member No.: 9,026
Region Association: Upper MidWest
If I were to do it over I would butt weld. Only because of the amount of body work I am looking at this time. I think the butt weld would have given me a smoother starting point.
I went with what he suggested because of his experience, and it was his shop that we did the work in.
I know some are thinking it’s my car I should have done it the way I wanted. For me I like the idea of a strong joint and hind sight is always 20/20. The end result is I have the flares welded on with from what I can see a good seem on both the inside and outside of the car.
I will be modifying my current rockers to match up with the flares so I get a perfect match. I heard many stories of them not lining up (some times more than an inch and a half) and call me cheap but if I’m going to pay $150 plus for some strips of fiberglass I would expect them to line up better than what I have heard they do.
The flares are from the group buy from AA
This is what I hope it will look like when all is said and done.

Attached Image


I will get those photos once I charge up the camera again.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
partwerks
post Dec 1 2011, 10:17 PM
Post #20


Senior Member
***

Group: Members
Posts: 1,598
Joined: 7-September 06
From: Grand Island, NE
Member No.: 6,787
Where can I get the front chrome bumper with the notch in it like the black car has?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

2 Pages V  1 2 >
Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Standard · Switch to: Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 23rd November 2024 - 05:17 AM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...