Oil Galley plugs.. steerl or alum., question for engine guys |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
Oil Galley plugs.. steerl or alum., question for engine guys |
MrHyde |
Mar 19 2012, 01:52 PM
Post
#1
|
Senior Member Group: Members Posts: 525 Joined: 13-October 10 From: Ontario, Canada Member No.: 12,268 Region Association: None |
I just dropped my engine case off at the machine shop to get the cylinder registers decked and oil galley plugs pulled and tapped. I Already have the 3/8"npt steel plugs and was asked by the machine shop if there was a special reason for using steel ones over aluminum. He brought up having the two metals expand/contract at same temps., etc. and I had no other response than " that seems to be what everyone uses"... Soooo.. I don't really want to seem like much of a fool, but why is it that we use steel npt galley plugs vs. aluminum ones ????
Thanks a bunch, Mike |
aircooledtechguy |
Mar 19 2012, 02:03 PM
Post
#2
|
The Aircooledtech Guy Group: Members Posts: 1,966 Joined: 8-November 08 From: Anacortes, WA Member No.: 9,730 Region Association: Pacific Northwest |
Use the steel ones. The aluminum ones can gall going in and you'll have to drill it out next time.
I also use a good thread sealer like the white Permatex liquid thread sealer; good stuff and I've never had a leak with it. |
gothspeed |
Mar 19 2012, 08:00 PM
Post
#3
|
Senior Member Group: Members Posts: 1,539 Joined: 3-February 09 From: SoCal Member No.: 10,019 Region Association: None |
I think mine were anodized aluminum. anodizing hardens the surface slightly and if used with sealant they should screw in just fine. I agree with the CTE argument.
|
Valy |
Mar 20 2012, 01:23 AM
Post
#4
|
Senior Member Group: Members Posts: 1,677 Joined: 6-April 10 From: Sunnyvale, CA Member No.: 11,573 Region Association: Northern California |
How about brass?
It's hard enough and expands/contracts similar to the aluminum. Just my 2 cents. |
MrHyde |
Mar 20 2012, 10:52 AM
Post
#5
|
Senior Member Group: Members Posts: 525 Joined: 13-October 10 From: Ontario, Canada Member No.: 12,268 Region Association: None |
Gonna stick with the steel ones... The engine will be far from stock, so I'll beef up what I can.. Thanks all
|
gothspeed |
Mar 20 2012, 04:01 PM
Post
#6
|
Senior Member Group: Members Posts: 1,539 Joined: 3-February 09 From: SoCal Member No.: 10,019 Region Association: None |
I believe the factory interference fit plugs are steel and sometimes fall out and leak ....... but they are not threaded either .......... so you should be fine. (IMG:style_emoticons/default/smile.gif)
|
Jake Raby |
Mar 20 2012, 04:29 PM
Post
#7
|
Engine Surgeon Group: Members Posts: 9,398 Joined: 31-August 03 From: Lost Member No.: 1,095 Region Association: South East States |
I believe the factory interference fit plugs are steel and sometimes fall out and leak ....... but they are not threaded either .......... so you should be fine. (IMG:style_emoticons/default/smile.gif) No, they are aluminum and have very little interference fit. We ONLY use steel plugs, 16 years later they can be removed with no issue and the galleys cleaned at rebuild.Just a little dab of Milk Of Magnesia on each plug is a good way to ensure they'll never seize. I have had horrible experiences with threaded aluminum plugs that we have removed from "core engines" that had them retrofitted. |
MrHyde |
Mar 20 2012, 04:46 PM
Post
#8
|
Senior Member Group: Members Posts: 525 Joined: 13-October 10 From: Ontario, Canada Member No.: 12,268 Region Association: None |
I'm going to try to minimize my exposure to the "horrible experiences"..
I'll stick with the steel ones.. I have them already anyways... Thanks for the Milk of Magnesia tip. ! Cheers |
gothspeed |
Mar 20 2012, 09:59 PM
Post
#9
|
Senior Member Group: Members Posts: 1,539 Joined: 3-February 09 From: SoCal Member No.: 10,019 Region Association: None |
I'm going to try to minimize my exposure to the "horrible experiences".. I'll stick with the steel ones.. I have them already anyways... Thanks for the Milk of Magnesia tip. ! Cheers I checked on my new 2056 engine build and the plugs are steel and have yet to leak. so the alloy ones I envisioned at my friends shop, must have been for something else. (IMG:style_emoticons/default/smash.gif) |
Lo-Fi Version | Time is now: 26th September 2024 - 11:54 AM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |