Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

2 Pages V  1 2 >  
 Reply to this topicStart new topic
> Floor tar, easiest way to remove?
Woody
post Jun 25 2012, 07:44 AM
Post #1


Sandbox Rabblerouser and head toilet scrubber
****

Group: Members
Posts: 3,858
Joined: 28-December 10
From: San Antonio Texas
Member No.: 12,530
Region Association: Southwest Region
What's the easiest way to get the sound deadening tar off the floor boards? It's time for my car to go on a diet and this stuff needs to go.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
jmill
post Jun 25 2012, 08:01 AM
Post #2


Green Hornet
****

Group: Members
Posts: 2,449
Joined: 9-May 08
From: Racine, Wisconsin
Member No.: 9,038
Region Association: Upper MidWest
Dry ice, dead blow hammer and a scraper.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
balljoint
post Jun 25 2012, 08:02 AM
Post #3


914 Wizard
**********

Group: Members
Posts: 10,000
Joined: 6-April 04
Member No.: 1,897
Region Association: None
When I did it I used a heat gun and a putty knife. Neat and tidy, no wire wheel wires sticking out of my clothes at the end of the day, no messy dust flung all over the place. Heat. Scrape. Dump into a bucket. Repeat.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Bartlett 914
post Jun 25 2012, 08:02 AM
Post #4


Advanced Member
****

Group: Members
Posts: 2,216
Joined: 30-August 05
From: South Elgin IL
Member No.: 4,707
Region Association: Upper MidWest
QUOTE(Woody @ Jun 25 2012, 08:44 AM) *

What's the easiest way to get the sound deadening tar off the floor boards? It's time for my car to go on a diet and this stuff needs to go.

I use a Mapp Gas torch (propane will work). Warm a small section at a time and use a wood chisel or putty knife.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
reharvey
post Jun 25 2012, 08:10 AM
Post #5


Senior Member
***

Group: Members
Posts: 573
Joined: 16-July 08
From: N. E. Ohio
Member No.: 9,308
Region Association: North East States
QUOTE(balljoint @ Jun 25 2012, 10:02 AM) *

When I did it I used a heat gun and a putty knife. Neat and tidy, no wire wheel wires sticking out of my clothes at the end of the day, no messy dust flung all over the place. Heat. Scrape. Dump into a bucket. Repeat.



(IMG:style_emoticons/default/agree.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
IronHillRestorations
post Jun 25 2012, 08:45 AM
Post #6


I. I. R. C.
*****

Group: Members
Posts: 6,768
Joined: 18-March 03
From: West TN
Member No.: 439
Region Association: None
Wood chisels
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
toolguy
post Jun 25 2012, 08:49 AM
Post #7


Senior Member
***

Group: Members
Posts: 1,273
Joined: 2-April 11
From: San Diego / El Cajon
Member No.: 12,889
Region Association: Southern California
Here's what I found worked the best with the least effort and mess. . On sale now Harbor Freight for $19.99 . . buy some extra of the scraper blades though. . and with the 30 day warranty you can use the hell out of it. . you don't need any heat or cold. . just plug in and go. . . you should be able to do you entire floor in an hour or so. . . only bad part is it make a hell of a racket. . .

http://www.harborfreight.com/oscillating-m...tool-68861.html


Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
rohar
post Jun 25 2012, 08:51 AM
Post #8


Senior Member
***

Group: Members
Posts: 924
Joined: 25-October 08
From: spokane
Member No.: 9,685
Region Association: None
One of these with the scraper blade. Amazingly simple and leaves things clean as a whistle.

Can cut through about a 12"x12" section in about a minute:

http://www.harborfreight.com/power-tools/o...tool-67537.html
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
rohar
post Jun 25 2012, 08:52 AM
Post #9


Senior Member
***

Group: Members
Posts: 924
Joined: 25-October 08
From: spokane
Member No.: 9,685
Region Association: None
almost simulpost toolguy!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
boogie_man
post Jun 25 2012, 08:57 AM
Post #10


Member
**

Group: Members
Posts: 308
Joined: 22-April 11
From: So Cal
Member No.: 12,969
Region Association: Southern California
QUOTE(reharvey @ Jun 25 2012, 07:10 AM) *

QUOTE(balljoint @ Jun 25 2012, 10:02 AM) *

When I did it I used a heat gun and a putty knife. Neat and tidy, no wire wheel wires sticking out of my clothes at the end of the day, no messy dust flung all over the place. Heat. Scrape. Dump into a bucket. Repeat.



(IMG:style_emoticons/default/agree.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
toolguy
post Jun 25 2012, 09:02 AM
Post #11


Senior Member
***

Group: Members
Posts: 1,273
Joined: 2-April 11
From: San Diego / El Cajon
Member No.: 12,889
Region Association: Southern California
simple minds think alike. . .
I tried everything i could think of and most of it was messy. . I stripped the entire car, everywhere in a week. . . Bad part was when i went inside in the evening, i realized how bad my ears were ringing from the noise. . On a bare tub, it's like you're inside a giant cymbal so you might think about soem ear protection. .

Back to the old "Homeowners complaint", this is what started the lady next door complaining. . .
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
OU8AVW
post Jun 25 2012, 09:34 AM
Post #12


Yacht Rigger
***

Group: Members
Posts: 1,803
Joined: 1-October 08
From: Granbury, TX
Member No.: 9,601
Region Association: Southwest Region
I told my 15 year old...."go get that black crap off the floor of my 914." Then I bought him some ice cream......
Easy!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bandjoey
post Jun 25 2012, 01:09 PM
Post #13


bandjoey
****

Group: Members
Posts: 4,930
Joined: 26-September 07
From: Bedford Tx
Member No.: 8,156
Region Association: Southwest Region
HF sells EarPlugs for the 1/2 hour it takes to take the tar off with the vibrator tool... (IMG:style_emoticons/default/beer3.gif)
User is online!Profile CardPM
Go to the top of the page
+Quote Post
stuttgart46
post Jun 25 2012, 01:22 PM
Post #14


Member
**

Group: Members
Posts: 305
Joined: 17-December 07
From: Santa Monica, CA
Member No.: 8,474
Region Association: None
QUOTE(OU8AVW @ Jun 25 2012, 07:34 AM) *

I told my 15 year old...."go get that black crap off the floor of my 914." Then I bought him some ice cream......
Easy!

And what a great way to spend a summer day. Great idea. I'm assuming this works with 14 year olds as well.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
ThePaintedMan
post Jun 25 2012, 01:22 PM
Post #15


Advanced Member
****

Group: Members
Posts: 3,886
Joined: 6-September 11
From: St. Petersburg, FL
Member No.: 13,527
Region Association: South East States
QUOTE(OU8AVW @ Jun 25 2012, 11:34 AM) *

I told my 15 year old...."go get that black crap off the floor of my 914." Then I bought him some ice cream......
Easy!



(IMG:style_emoticons/default/beerchug.gif) (IMG:style_emoticons/default/av-943.gif) Here's to manual labor!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
TheCabinetmaker
post Jun 25 2012, 02:02 PM
Post #16


I drive my car everyday
*****

Group: Members
Posts: 8,318
Joined: 8-May 03
From: Tulsa, Ok.
Member No.: 666
QUOTE(ThePaintedMan @ Jun 25 2012, 02:22 PM) *

QUOTE(OU8AVW @ Jun 25 2012, 11:34 AM) *

I told my 15 year old...."go get that black crap off the floor of my 914." Then I bought him some ice cream......
Easy!



(IMG:style_emoticons/default/beerchug.gif) (IMG:style_emoticons/default/av-943.gif) Here's to manual labor!

Thats only if your son is named Manual. (IMG:style_emoticons/default/laugh.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
MikeSpraggi
post Jun 25 2012, 04:04 PM
Post #17


Senior Member
***

Group: Members
Posts: 781
Joined: 7-February 05
From: Silver Spring, Md
Member No.: 3,570
Region Association: MidAtlantic Region
QUOTE(Bartlett 914 @ Jun 25 2012, 07:02 AM) *

QUOTE(Woody @ Jun 25 2012, 08:44 AM) *

What's the easiest way to get the sound deadening tar off the floor boards? It's time for my car to go on a diet and this stuff needs to go.

I use a Mapp Gas torch (propane will work). Warm a small section at a time and use a wood chisel or putty knife.


(IMG:style_emoticons/default/agree.gif) This method was really easy and effective.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
SirAndy
post Jun 25 2012, 06:01 PM
Post #18


Resident German
*************************

Group: Admin
Posts: 41,854
Joined: 21-January 03
From: Oakland, Kalifornia
Member No.: 179
Region Association: Northern California
QUOTE(balljoint @ Jun 25 2012, 07:02 AM) *
heat gun and a putty knife

(IMG:style_emoticons/default/agree.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Rand
post Jun 25 2012, 06:14 PM
Post #19


Cross Member
*****

Group: Members
Posts: 7,409
Joined: 8-February 05
From: OR
Member No.: 3,573
Region Association: None
Ayup, heat is your friend. Follow the glue lines and it lets go quickly. A wide blade peels it off fast. Many threads on this.

As I've said before, I can have the tar out of at least one side of the floorboard with tools in my garage before you can even get back here with dry ice. (Although dry ice is fun too. Make sure you pick up a case of plastic water bottles while you're at it. (IMG:style_emoticons/default/happy11.gif) )
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Woody
post Jun 25 2012, 06:32 PM
Post #20


Sandbox Rabblerouser and head toilet scrubber
****

Group: Members
Posts: 3,858
Joined: 28-December 10
From: San Antonio Texas
Member No.: 12,530
Region Association: Southwest Region
Thanks guys. I'll definitely try the heat method. (IMG:style_emoticons/default/beerchug.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

2 Pages V  1 2 >
Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Standard · Switch to: Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 31st October 2024 - 07:24 PM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...