![]() |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
![]() |
bbrock |
![]()
Post
#1
|
914 Guru ![]() ![]() ![]() ![]() ![]() Group: Members Posts: 5,269 Joined: 17-February 17 From: Montana Member No.: 20,845 Region Association: Rocky Mountains ![]() ![]() |
I'm refurbishing my main wire harness and looking for suggestions for sourcing sleeve material to replace my brittle and oversprayed stuff. I know I can get PVC sleeve from McMaster-Carr as described in this old thread. But this doesn't quite get me there.
There are two sections of sleeve before and after where the two headlight circuits branch that are slit and taped sleeves. I'm thinking just buy some oversized PVC sleeve for that and slit it myself unless someone has a better idea. On the rest, the small diameter sleeve appears to be heat shrink and maybe all of it is. Regardless, you can't get a tight factory fit with plain PVC sleeve without removing all, or most, of the terminals. I'd like to avoid that. So wondering what heat shrink material would have the same glossy black finish as the original sleeves. Thanks for any advice. (IMG:style_emoticons/default/popcorn[1].gif) |
![]() ![]() |
jd74914 |
![]()
Post
#2
|
Its alive ![]() ![]() ![]() ![]() Group: Members Posts: 4,782 Joined: 16-February 04 From: CT Member No.: 1,659 Region Association: North East States ![]() |
Have you seen this 2:1 shrink from Techflex? Might not be a high enough shrink ratio to get the terminals through, but I'm not sure.
https://www.techflex.com/prod_h2g.asp Note: Never used it, but have been happy with other Techflex products. |
bbrock |
![]()
Post
#3
|
914 Guru ![]() ![]() ![]() ![]() ![]() Group: Members Posts: 5,269 Joined: 17-February 17 From: Montana Member No.: 20,845 Region Association: Rocky Mountains ![]() ![]() |
Have you seen this 2:1 shrink from Techflex? Might not be a high enough shrink ratio to get the terminals through, but I'm not sure. https://www.techflex.com/prod_h2g.asp Note: Never used it, but have been happy with other Techflex products. Haven't seen it and looks promising. I think 2:1 should work. The factory sleeve isn't sucked down too tight anyway and 2:1 should be plenty to get wires with spade terminals through. Obviously large plastic connectors have to come off. But those come off installing the harness anyway. I've googled and searched on ebay and found lots of stuff that might work. But pictures and descriptions were too vague to know how the finish looks. Thanks! |
aharder |
![]()
Post
#4
|
Advanced Member ![]() ![]() ![]() ![]() Group: Members Posts: 4,427 Joined: 6-September 11 From: Dallas Texas Member No.: 13,524 Region Association: Southwest Region ![]() ![]() |
I used Convoluted Tubing, available at most parts houses and come in different diameters
![]() |
IronHillRestorations |
![]()
Post
#5
|
I. I. R. C. ![]() ![]() ![]() ![]() ![]() Group: Members Posts: 6,734 Joined: 18-March 03 From: West TN Member No.: 439 Region Association: None ![]() ![]() |
PM sent
|
sithot |
![]()
Post
#6
|
Member ![]() ![]() Group: Members Posts: 446 Joined: 25-October 06 From: Virginia Member No.: 7,090 Region Association: None ![]() ![]() |
A friend just bought Flexo Woven Wrap TechFlex Mesh Netting for his RASANT/PMO EFI setup. Al Kosmal put it together, however, he was seeking further protection. I've bought from McMaster but I like what he purchased a lot.
https://www.showmecables.com/catalogsearch/...;q=+flexo+woven |
bbrock |
![]()
Post
#7
|
914 Guru ![]() ![]() ![]() ![]() ![]() Group: Members Posts: 5,269 Joined: 17-February 17 From: Montana Member No.: 20,845 Region Association: Rocky Mountains ![]() ![]() |
If I wasn't so anal about getting the factory stock look, the mesh stuff is what I would use. I think it's a better loom sleeve, but not "vintage." (IMG:style_emoticons/default/beer.gif)
|
914 Ranch |
![]()
Post
#8
|
Team Sharp where the 914 grow wings ![]() ![]() ![]() Group: Members Posts: 1,421 Joined: 29-January 16 From: TheNorth Shore Retreat. Deland Member No.: 19,611 Region Association: South East States ![]() |
|
![]() ![]() |
![]() |
Lo-Fi Version | Time is now: 25th June 2024 - 12:47 AM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |