Sail trim clip holes |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
Sail trim clip holes |
BPic |
Dec 21 2018, 01:28 PM
Post
#1
|
Member Group: Members Posts: 341 Joined: 5-February 18 From: Miami, Florida Member No.: 21,864 Region Association: South East States |
Ok, so the PO removed and filled the holes for the chrome piece clips. I know that the one to the rear gets a nut but what do the other 2 get to secure it?
I have all the seam sealer off and want to fix it now if I need to add something. Thanks all! And I hope everyone here on 914WORLD has a great holiday season and a healthy, happy, and 914 new year!! All the best to all of you! |
IronHillRestorations |
Dec 21 2018, 02:04 PM
Post
#2
|
I. I. R. C. Group: Members Posts: 6,759 Joined: 18-March 03 From: West TN Member No.: 439 Region Association: None |
There's a special V shaped clip that goes in the lower sail trim and springs into the holes
|
BPic |
Dec 21 2018, 03:01 PM
Post
#3
|
Member Group: Members Posts: 341 Joined: 5-February 18 From: Miami, Florida Member No.: 21,864 Region Association: South East States |
So no nuts welded in place etc. the clip itself holds the hole?
|
rhodyguy |
Dec 21 2018, 03:20 PM
Post
#4
|
Chimp Sanctuary NW. Check it out. Group: Members Posts: 22,188 Joined: 2-March 03 From: Orion's Bell. The BELL! Member No.: 378 Region Association: Galt's Gulch |
Correct.
|
dr914@autoatlanta.com |
Dec 21 2018, 03:39 PM
Post
#5
|
914 Guru Group: Members Posts: 8,053 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None |
if you look side ways at the sail just before it flares out onto the quarter panel you may be able to see where the four holes used to be. Good man for reinstalling the vinyl. Here is a reference picture for the v clips with the part number:
http://www.autoatlanta.com/porsche-parts/h...;section=810-00 Ok, so the PO removed and filled the holes for the chrome piece clips. I know that the one to the rear gets a nut but what do the other 2 get to secure it? I have all the seam sealer off and want to fix it now if I need to add something. Thanks all! And I hope everyone here on 914WORLD has a great holiday season and a healthy, happy, and 914 new year!! All the best to all of you! |
BPic |
Dec 21 2018, 03:52 PM
Post
#6
|
Member Group: Members Posts: 341 Joined: 5-February 18 From: Miami, Florida Member No.: 21,864 Region Association: South East States |
Thanks George. Makes sense now.
BTW do you carry the channel that the frunk rubber seal sits in? Thanks again... if you look side ways at the sail just before it flares out onto the quarter panel you may be able to see where the four holes used to be. Good man for reinstalling the vinyl. Here is a reference picture for the v clips with the part number: http://www.autoatlanta.com/porsche-parts/h...;section=810-00 Ok, so the PO removed and filled the holes for the chrome piece clips. I know that the one to the rear gets a nut but what do the other 2 get to secure it? I have all the seam sealer off and want to fix it now if I need to add something. Thanks all! And I hope everyone here on 914WORLD has a great holiday season and a healthy, happy, and 914 new year!! All the best to all of you! |
rhodyguy |
Dec 21 2018, 03:58 PM
Post
#7
|
Chimp Sanctuary NW. Check it out. Group: Members Posts: 22,188 Joined: 2-March 03 From: Orion's Bell. The BELL! Member No.: 378 Region Association: Galt's Gulch |
On that exploded parts diagram are items 26-32 for mud flaps? How would the hw mount?
|
dr914@autoatlanta.com |
Dec 21 2018, 04:49 PM
Post
#8
|
914 Guru Group: Members Posts: 8,053 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None |
|
aharder |
Dec 21 2018, 08:26 PM
Post
#9
|
Advanced Member Group: Members Posts: 4,509 Joined: 6-September 11 From: Dallas Texas Member No.: 13,524 Region Association: Southwest Region |
I'm currently working on the Sail Trim.
Hope this helps |
buck toenges |
Dec 24 2018, 10:57 PM
Post
#10
|
Senior Member Group: Members Posts: 553 Joined: 25-November 03 From: Fort wayne In Member No.: 1,388 Region Association: None |
What are the factory spec sizes for the holes? If you add these after the car has been painted what do you use to protect the holes from rust? How do you apply the protection?
Buck |
IronHillRestorations |
Dec 25 2018, 07:13 AM
Post
#11
|
I. I. R. C. Group: Members Posts: 6,759 Joined: 18-March 03 From: West TN Member No.: 439 Region Association: None |
The factory used something kind of like butyl (like the windshield tape) and put a wad all around the clip. I don't know if the holes were painted after they got drilled, but I take great care to make sure they are coated.
|
Lo-Fi Version | Time is now: 24th September 2024 - 01:04 PM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |