 Rubber bumpers for bil's, Say that five times fast! |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| Jaiden |
 Mar 7 2006, 08:26 AM
Post
#1
|
|
Member  Group: Members Posts: 346 Joined: 13-January 05 From: Stroudsburg PA Member No.: 3,443  |
So when I go to install my new Bilstein inserts do you reuse the stock rubber bumpers? They really don't fit over the shaft of the bils.
Should there be something there? Or do I forget about them? |
   |
 
|
| redshift |
Mar 7 2006, 08:50 AM
Post
#2
|
|
Bless the Hell out of you! Group: Members Posts: 10,926 Joined: 29-June 03 Member No.: 869 |
You need snubbers. Buy new ones.
M |
|
|
|
| Jaiden |
Mar 7 2006, 09:06 AM
Post
#3
|
|
Member Group: Members Posts: 346 Joined: 13-January 05 From: Stroudsburg PA Member No.: 3,443 |
Care to elaborate? I haven'tseen this mentioned and I did not receive new ones from Pelican when I got my struts. Are these new ones a different dimension and where who I find these parts?
Thanks! |
|
|
|
| JWest |
Mar 7 2006, 09:14 AM
Post
#4
|
|
Senior Member Group: Members Posts: 1,662 Joined: 6-January 03 From: Fort Worth, TX Member No.: 97 Region Association: None 
|
Are these Bils in Boge struts? If so, the snubber in installed in the lower part of the tube already (you can't get to it).
Bils in Bil struts with the small lower shaft and roll pin? You need to install the snubber on the lower shaft. |
|
|
|
| Jaiden |
Mar 7 2006, 09:21 AM
Post
#5
|
|
Member Group: Members Posts: 346 Joined: 13-January 05 From: Stroudsburg PA Member No.: 3,443 |
These are Front Boge strut housings with new bil inserts. I'm talking about at the top of the strut the "rubber spring" that sits on the strut below the top cover. DO I need to reinstall these?
|
|
|
|
| JWest |
Mar 7 2006, 09:45 AM
Post
#6
|
|
Senior Member Group: Members Posts: 1,662 Joined: 6-January 03 From: Fort Worth, TX Member No.: 97 Region Association: None
|
No, it is installed in the lower part of the tube already but you can't see it. The Bils for Boges are strange in that the fluid is in the upper chromed shaft, and a small shaft is inside the painted tube that fits into the strut housing. The bump stop is inside that lower painted tube.
|
|
|
|
| Jaiden |
Mar 7 2006, 09:57 AM
Post
#7
|
|
Member Group: Members Posts: 346 Joined: 13-January 05 From: Stroudsburg PA Member No.: 3,443 |
Thanks.
Oh one last question the little rubber washer that is below the nut on the struts. Does that go below or above the strut mount. I was thinking below were the cover meets the bushing. I can't wait to get all of this back together an back on the road. |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 31st October 2024 - 08:25 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.