Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

861 Pages V « < 4 5 6 7 8 > »   
 Reply to this topicStart new topic
> what did you do to your 914 today
stewteral
post Dec 30 2011, 10:52 PM
Post #101


Old Member
**

Group: Members
Posts: 384
Joined: 4-December 07
From: Camarillo, CA
Member No.: 8,424
Region Association: Southern California
QUOTE(TC 914-8 @ Dec 30 2011, 05:30 PM) *

Thought it would be a good idea to pull my oil pan (SBC) and fix some oil leaks with a new Felpro 1 peice pan gasket. Got it all together and oil poured out of the front pan seal worse than before. Turns out Felpro makes several types. Thick front seal / thin front seal. $35.00 later I bought the thick front seal, one peice gasket. got it all together, full of new oil and she's ready to run.
Took her for a run around the block, no leaks, all is good for now.
Any SBC's or V8's out there I recommend the one piece gasket, they seal like a champ and very easy to install, so easy I did it twice (IMG:style_emoticons/default/av-943.gif)


Hey TC 914-8,

I've gone to the single rubber gasket on my SBC too.....but is there REALLY a Chevy that DOESN'T LEAK? My achilles heal seems to be the damned 2-piece main seal.

Best,
Terry
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Eddie914
post Dec 31 2011, 12:21 PM
Post #102


Unregistered
Working on the front brakes ... installing Wilwood Superlite II 4 piston calipers and 309mm x 32mm rotors.

It's a bit more than a "bolt-on".

sixnotfour fabricated custom rotor hats.

I'm close to getting the custom adapters finished.

There is some interference with the BBS e50 16 x 8 front wheels (bolts that hold the hoops to the center)

Stay tuned!

Cheers,

Eddie
Go to the top of the page
+Quote Post
VRROOMM1
post Dec 31 2011, 12:41 PM
Post #103


Member
**

Group: Members
Posts: 117
Joined: 15-July 08
From: mt. dora fl
Member No.: 9,302
Region Association: South East States
rebilt carb and changed fuel filter
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
rohar
post Dec 31 2011, 12:44 PM
Post #104


Senior Member
***

Group: Members
Posts: 924
Joined: 25-October 08
From: spokane
Member No.: 9,685
Region Association: None
I'm gonna get the v8 bolted into the car this weekend if it kills me. It just might.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
DRPHIL914
post Dec 31 2011, 12:46 PM
Post #105


Dr. Phil
*****

Group: Members
Posts: 5,810
Joined: 9-December 09
From: Bluffton, SC
Member No.: 11,106
Region Association: South East States
New c.h.t. and injection points plate, reset timing. Smoooooth!!!!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
3d914
post Dec 31 2011, 04:58 PM
Post #106


Senior Member
***

Group: Members
Posts: 1,275
Joined: 24-September 03
From: Benson, AZ
Member No.: 1,191
Region Association: Southwest Region
Building this . . .
(IMG:http://www.914world.com/bbs2/uploads/post-1191-1325195079.jpg)

to test & put this . . .
(IMG:http://www.914world.com/bbs2/uploads/post-1191-1241407062.jpg)

in here . . .
(IMG:http://www.914world.com/bbs2/uploads/post-1191-1207882655.jpg)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
PeeGreen 914
post Dec 31 2011, 08:40 PM
Post #107


Just when you think you're done...wait, there is more..lol
**********

Group: Members
Posts: 10,219
Joined: 21-September 06
From: Seattle, WA... actually Everett
Member No.: 6,884
Region Association: Pacific Northwest
Installed new front bushings. Still need to fine tune them but they are on the car now (IMG:style_emoticons/default/smile.gif)


Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Randal
post Dec 31 2011, 08:46 PM
Post #108


Advanced Member
****

Group: Members
Posts: 4,446
Joined: 29-May 03
From: Los Altos, CA
Member No.: 750

Went to get the car out of the garage and loaded on the trailer. Starter her up and had a miss. Well 3 hours later I think I have it fixed, but we'll see tomorrow morning.

Great way to start the year, heading down to the Marina for their first event of the year. (IMG:style_emoticons/default/driving.gif)

User is offlineProfile CardPM
Go to the top of the page
+Quote Post
rohar
post Dec 31 2011, 08:56 PM
Post #109


Senior Member
***

Group: Members
Posts: 924
Joined: 25-October 08
From: spokane
Member No.: 9,685
Region Association: None
QUOTE(PeeGreen 914 @ Dec 31 2011, 06:40 PM) *

Installed new front bushings. Still need to fine tune them but they are on the car now (IMG:style_emoticons/default/smile.gif)



WOOT!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
hot_shoe914
post Dec 31 2011, 09:00 PM
Post #110


on ramp passer
****

Group: Members
Posts: 3,806
Joined: 20-November 07
From: Earle, Ar.
Member No.: 8,354
Region Association: None
I just (IMG:style_emoticons/default/driving.gif) the (IMG:style_emoticons/default/stromberg.gif) out of the LE. Christine gets her turn tomorrow. (IMG:style_emoticons/default/driving.gif) Okay fine, for all you people that think I never work on my cars and just drive them I did INSTALL new front euro lenses on the front of the LE today.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
partwerks
post Dec 31 2011, 09:24 PM
Post #111


Senior Member
***

Group: Members
Posts: 1,598
Joined: 7-September 06
From: Grand Island, NE
Member No.: 6,787
Changed oil in it today and lubed the speedometer cable.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
JRust
post Dec 31 2011, 09:56 PM
Post #112


914 Guru
*****

Group: Members
Posts: 6,310
Joined: 10-January 03
From: Corvallis Oregon
Member No.: 129
Region Association: Pacific Northwest
Played musical 914's & trailers (IMG:style_emoticons/default/blink.gif)
Started by pulling my trailer around the barn to the front. I loaded my Creamsicle in the trailer to paint the trunks. I can't get my barn warm enough to paint. I am doing the front & back trunks. So there is enough room to spray from the front & back. It took a little doing getting it in the trailer. I was by myself & while I got a new winch for xmas. I didn't have everything I needed to install it. So I said to myself hey I'll just start it & drive it up. So I dig around to find my keys for it. I find them & go out to start it. Oh yeah I don't have my pedal assembly in. I'm not ready to put it back in either. So it was back to thinking about how to get it in. I went ahead & started my LE to let it warm up. I decided to start it in 1st & drive it up. I turned it off a couple times on the way up. I didn't want to chance running into the front of the trailer. I don't have my ebrake hooked up either (IMG:style_emoticons/default/dry.gif) . I managed to load it without screwing anything up though (IMG:style_emoticons/default/biggrin.gif) .

Next I moved my wrecked 74 into the bay in the barn. I'll start tearing into it soon.

Next I backed my trailer up parallel to the front of my barn. It is nice & close to go out to work on it. Plus easy to get power to it.

After that I got all my lights turned on in the trailer & hooked up some heat. Did a little work sanding the rear trunk & put one more coat of primer down. I am going to practice painting some tomorrow. If all goes well with that. I will shoot both trunks on monday (IMG:style_emoticons/default/popcorn[1].gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
toolguy
post Jan 1 2012, 03:15 PM
Post #113


Senior Member
***

Group: Members
Posts: 1,275
Joined: 2-April 11
From: San Diego / El Cajon
Member No.: 12,889
Region Association: Southern California
9 months full time restoration , around 1500 hours so far. . my goal was the have it done in one year. . and I spent the last day of 2011 stuffing the engine. . it's getting close. .


Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
SUNAB914
post Jan 1 2012, 03:26 PM
Post #114


Senior Member
***

Group: Members
Posts: 698
Joined: 29-December 08
From: Fredericksburg VA
Member No.: 9,880
Region Association: South East States
Washed both 914s and took each of them for a short drive. Both in garage so I can wax them tomorrow, maybe..
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
dlee6204
post Jan 1 2012, 03:51 PM
Post #115


Howdy
****

Group: Members
Posts: 2,162
Joined: 30-April 06
From: Burnsville, NC
Member No.: 5,956
I found out why my alternator wasn't charging completely and fixed it (IMG:style_emoticons/default/smile.gif) Then I took it for a nice long drive. (IMG:style_emoticons/default/driving.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
mrbubblehead
post Jan 1 2012, 08:23 PM
Post #116


Twodollardoug
***

Group: Members
Posts: 1,155
Joined: 17-December 10
From: calimesa ca.
Member No.: 12,492
Region Association: Southern California
QUOTE(toolguy @ Jan 1 2012, 01:15 PM) *

9 months full time restoration , around 1500 hours so far. . my goal was the have it done in one year. . and I spent the last day of 2011 stuffing the engine. . it's getting close. .
WOW!!!! that is beautiful... very nice work.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
mrbubblehead
post Jan 2 2012, 10:21 PM
Post #117


Twodollardoug
***

Group: Members
Posts: 1,155
Joined: 17-December 10
From: calimesa ca.
Member No.: 12,492
Region Association: Southern California
i finally finished my engman stiffiner kit install. painted the interior and got everything put back together. now im ready for carpet.
(IMG:http://www.914world.com/bbs2/uploads_offsite/i722.photobucket.com-12492-1325564493.1.jpg)

today i started build and early set of doors. im making them to use late window regulators. im gonna repaint them olympic blue. and put new rubber and felt. right now i have one late door and one early.....the ratteling is driving me crazy. (IMG:style_emoticons/default/hissyfit.gif)
(IMG:http://www.914world.com/bbs2/uploads_offsite/i722.photobucket.com-12492-1325564493.2.jpg)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
RickS
post Jan 2 2012, 11:25 PM
Post #118


Senior Member
***

Group: Members
Posts: 1,408
Joined: 17-April 06
From: 'False City', WA
Member No.: 5,880
Region Association: None
Bought an LED third brake light which I will tuck under the center of the targa bar so it's invisible until activated - then it will obnoxiously pulse 4 flashes and then go to solid red when the brakes are applied. It should definitely gets the attention of cell phone yacking, latte swilling, soccer moms in their SUVs. Saw the same deal on the back of a motor cycle cop's bike and it really stands out. Not period but if it saves me from being rear ended, then its cool - besides, I don't have to look at it. Knight Rider Sequential 12 LED Light Bar with Flashing Brake Alert - RED - they have a video of it too - http://www.customdynamics.com/knight_rider_led_light_bar.htm
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
SirAndy
post Jan 3 2012, 12:08 PM
Post #119


Resident German
*************************

Group: Admin
Posts: 41,894
Joined: 21-January 03
From: Oakland, Kalifornia
Member No.: 179
Region Association: Northern California
QUOTE
what did you do to your 914 today

Drove it! (IMG:style_emoticons/default/happy11.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
fteixeira
post Jan 3 2012, 05:15 PM
Post #120


Newbie
*

Group: Members
Posts: 32
Joined: 25-February 11
From: Santa Clara, CA
Member No.: 12,754
Region Association: None
QUOTE
QUOTE(wndsrfr @ Dec 29 2011, 05:33 PM) *

Last weekend: new rear rotors and rear brake pad clearance adjustment. Where can I get the caliper adjustment gear caps with the 4mm allen hex with the copper washer? The original aluminum onse are stripped to hell. I thought I saw someone selling them here at one point... in steel? Eric Shea?

This weekend: bleeding brakes single-handed. No way I'm asking the wife for help (divorce is expensive in California). Wish me luck.

fteixeira


Yep, Eric's got 'em at PMB, super fast shipping with USPS Priority Mail, too. I've just mounted up "speed bleeders", works like a champ.


Well, yesterday, I was able to very effectively bleed the brakes with speed-bleeders in the rear and using a mity-vac on the fronts. Used Pentosin Dot4. Worked very well and I got a good firm brake pedal.

After I put the wheels back on and was ready to take the car off the jack-stands, I noticed some brake-fluid on the ground. Searching like crazy to find the leak, and dang, it turns out its weeping out of the rear-right rubber break-line! Not the connection, but along the rubber line itself! This thing must be ready to pop. Ordered new lines today, and looking forward (not!) to redoing the bleed.... again.

fteixeira
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

861 Pages V « < 4 5 6 7 8 > » 
Reply to this topicStart new topic
5 User(s) are reading this topic (5 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Standard · Switch to: Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 25th November 2024 - 11:52 AM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...