Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

861 Pages V « < 10 11 12 13 14 > »   
 Reply to this topicStart new topic
> what did you do to your 914 today
AndyB
post Jan 15 2012, 07:02 PM
Post #221


The Governor is watching me
***

Group: Members
Posts: 1,115
Joined: 10-April 10
From: Philadelphia New York
Member No.: 11,595
Region Association: North East States
Finally completed my 5 guage center console cluster (IMG:style_emoticons/default/piratenanner.gif) (IMG:style_emoticons/default/drunk.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
914-300Hemi
post Jan 15 2012, 07:02 PM
Post #222


Senior Member
***

Group: Members
Posts: 1,369
Joined: 7-September 06
From: San Dimas, CA
Member No.: 6,794
Region Association: Southern California
I finished the electrical, charged the battery, connected the fuel line, and put gas in the gas tank. The next thing I did was look for the key and turned over the engine and got it started. (IMG:style_emoticons/default/piratenanner.gif)


User is offlineProfile CardPM
Go to the top of the page
+Quote Post
ELLIOTT
post Jan 15 2012, 07:22 PM
Post #223


Member
**

Group: Members
Posts: 103
Joined: 7-March 10
From: St.Hedwig Tx.
Member No.: 11,438
Region Association: None
Fixed the drivers side window, now I can roll it up , wooohooo
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Bob L.
post Jan 15 2012, 08:01 PM
Post #224


Senior Member
***

Group: Members
Posts: 848
Joined: 7-August 11
From: Austin TX
Member No.: 13,411
Region Association: Southwest Region
Got it started again after cleaning out the fuel system. (IMG:style_emoticons/default/piratenanner.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
jimkelly
post Jan 15 2012, 08:03 PM
Post #225


Delaware USA
****

Group: Members
Posts: 4,969
Joined: 5-August 04
From: Delaware, USA
Member No.: 2,460
Region Association: MidAtlantic Region
looked at it and cried (IMG:style_emoticons/default/hissyfit.gif)


Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
DRPHIL914
post Jan 15 2012, 08:06 PM
Post #226


Dr. Phil
*****

Group: Members
Posts: 5,810
Joined: 9-December 09
From: Bluffton, SC
Member No.: 11,106
Region Association: South East States
Put new outer door seals on both doors
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
sixaddict
post Jan 15 2012, 08:06 PM
Post #227


Senior Member
***

Group: Members
Posts: 863
Joined: 22-January 09
From: Panama City Beach, FL
Member No.: 9,961
Region Association: South East States
Removed front wall/bulkhead and one headlight light bucket so body man can install new one. Minor damage major workk. I am whipped ...body panel removal for kids
I am happy (IMG:style_emoticons/default/smoke.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
hot_shoe914
post Jan 15 2012, 08:18 PM
Post #228


on ramp passer
****

Group: Members
Posts: 3,806
Joined: 20-November 07
From: Earle, Ar.
Member No.: 8,354
Region Association: None
Tore down the motor from my parts car to see if the heads were any good. (IMG:style_emoticons/default/ar15.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
montoya 73 2.0
post Jan 15 2012, 08:59 PM
Post #229


Lack of consideration to others, and Selfish!
***

Group: Members
Posts: 1,791
Joined: 27-October 04
From: Paso Robles, Ca.
Member No.: 3,016
Region Association: Central California
Talked with McMark about building my motor! Hey, thats more than I have done in the last 4 months.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
nsr-jamie
post Jan 15 2012, 09:45 PM
Post #230


914 guy in Japan
***

Group: Members
Posts: 1,182
Joined: 7-November 07
From: Nagoya, Japan
Member No.: 8,305
Region Association: None
Finally added a fire extinguisher
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Black22
post Jan 15 2012, 09:56 PM
Post #231


Senior Member
***

Group: Members
Posts: 886
Joined: 1-November 07
From: Creswell, OR
Member No.: 8,290
Region Association: Pacific Northwest
Started to install a front sway bar and then found some rust. I then treated the rust (IMG:style_emoticons/default/sawzall-smiley.gif) (IMG:style_emoticons/default/welder.gif) , degreased my trans and cleaned out my gas tank all at the same time. (IMG:style_emoticons/default/wacko.gif)

I get side tracked easily, so I ended up only installing one sway bar mount! (IMG:style_emoticons/default/headbang.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
slimeygecko
post Jan 15 2012, 11:14 PM
Post #232


Newbie
*

Group: Members
Posts: 3
Joined: 15-February 05
From: Rexburg, ID
Member No.: 3,608
Region Association: Southwest Region
I completed my first engine drop to get at the tranny! It's gonna get rebuilt in the next couple of weeks while the wife is gone (IMG:style_emoticons/default/biggrin.gif)

Mike

Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
65tuxedo
post Jan 15 2012, 11:21 PM
Post #233


Newbie
*

Group: Members
Posts: 5
Joined: 8-January 12
From: Grand Lake, Ok
Member No.: 13,977
Region Association: None
While trying to get my 72. 1.7. To start, I pulled the points, bent them into shape, cleaned and set them. This didn't make it start but it did fix the tach which was going crazy when I drove it. Fixed the starting with a new fuse under the hood.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
aharder
post Jan 15 2012, 11:23 PM
Post #234


Advanced Member
****

Group: Members
Posts: 4,565
Joined: 6-September 11
From: Dallas Texas
Member No.: 13,524
Region Association: Southwest Region
Pulled the rear trunk hinges, cleaned and painted, Getting her ready for
a JWest Pivot Kit (IMG:style_emoticons/default/biggrin.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
pilothyer
post Jan 15 2012, 11:29 PM
Post #235


Member
***

Group: Members
Posts: 838
Joined: 21-May 08
From: N. Alabama
Member No.: 9,080
Region Association: South East States
Removed the rear brake calipers to rebuild, replaced rear rubber brake lines (PITA) Then disassembled the calipers to clean up and rebuild tomorrow...........Not alot but a little every day will help me run out of things to do on this one........ eventually........I hope..........Jerry
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
aharder
post Jan 16 2012, 05:03 PM
Post #236


Advanced Member
****

Group: Members
Posts: 4,565
Joined: 6-September 11
From: Dallas Texas
Member No.: 13,524
Region Association: Southwest Region
QUOTE(Scarlet75 @ Jan 15 2012, 07:02 PM) *

Finally completed my 5 guage center console cluster (IMG:style_emoticons/default/piratenanner.gif) (IMG:style_emoticons/default/drunk.gif)


Andy,

Do we get to see this 5 guage cluster (IMG:style_emoticons/default/huh.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
effutuo101
post Jan 16 2012, 05:26 PM
Post #237


Advanced Member
****

Group: Members
Posts: 2,735
Joined: 10-April 05
From: Lemon Grove
Member No.: 3,914
Region Association: Southern California
Built intake scoops for my rocker panels to feed the rear brakes.
Built side intake scoops for my rear quarters to feed the beast with a little forced air induction.
Made an absolute mess of my garage with fiberglass debris, wax paper and discarded mold materials.
Got side panel marked for potential placement of air scoop.
Realized that I have a Vespa in my garage.
Realized that both of my bikes haven't been ridden in months.
Watched some Dakar Rally.

tonight, sand scoops, cut fenders and rockers.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
PeeGreen 914
post Jan 16 2012, 05:53 PM
Post #238


Just when you think you're done...wait, there is more..lol
**********

Group: Members
Posts: 10,219
Joined: 21-September 06
From: Seattle, WA... actually Everett
Member No.: 6,884
Region Association: Pacific Northwest
Nice (IMG:style_emoticons/default/smile.gif) Sounds like your car is coming along Chris. I didn't know you were back.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
timofly
post Jan 16 2012, 06:48 PM
Post #239


Member
**

Group: Members
Posts: 164
Joined: 21-February 09
From: VA
Member No.: 10,082
Region Association: MidAtlantic Region
Repaired the horn, put on better sail panel trim pieces, boxed up a bunch of parts for Bill, thought about all the other shit I should be doing, said "the hell with it" and took it out to run the "mountain". I think this was it for winter, since the morons in town started putting salt down for a 1/2 inch snowfall last week!

Man, this car loves the cold weather, but salt is a killer, so into the barn he goes, covered with plastic, tank with almost full fuel and stabilizer and 35 psi in the tires. Sigh...see you in April.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
raw1298
post Jan 16 2012, 08:21 PM
Post #240


Senior Member
***

Group: Members
Posts: 616
Joined: 9-March 09
From: Rocklin,Ca.
Member No.: 10,148
Region Association: Northern California
Adjusted the valve using the Capn' method. Replaced a few connecters in the wiring harness. Chased down a couple of vacume leaks. Car is running much smoother now.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

861 Pages V « < 10 11 12 13 14 > » 
Reply to this topicStart new topic
6 User(s) are reading this topic (6 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Standard · Switch to: Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 25th November 2024 - 03:29 PM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...