Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

2 Pages V  1 2 >  
 Reply to this topicStart new topic
> Does anybody else besides me have trouble,, getting keeping their NUTS tight!? (trailing arm nuts)
root
post May 17 2006, 06:07 AM
Post #1


Two Wheeled Type4 Completed!
***

Group: Members
Posts: 849
Joined: 5-May 04
From: Sterling, VA
Member No.: 2,026
Region Association: None
My trailing arm nuts keep coming loose. Guess I just need to replace them new ones or with nylon lock nuts. Anybody know the thread size off hand? (IMG:style_emoticons/default/confused24.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Joe Ricard
post May 17 2006, 07:29 AM
Post #2


CUMONIWANNARACEU
*****

Group: Members
Posts: 6,811
Joined: 5-January 03
From: Gautier, MS
Member No.: 92
I don't know but I am now going to put that on my list of things to check. I get them pretty tight however. Poly bushings.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
GBallantine
post May 17 2006, 07:39 AM
Post #3


Member
**

Group: Members
Posts: 74
Joined: 12-October 04
From: Toronto,Ont.Canada
Member No.: 2,930
QUOTE(Joe Ricard @ May 17 2006, 05:29 AM) *

I don't know but I am now going to put that on my list of things to check. I get them pretty tight however. Poly bushings.


Common problem. I check mine after every race day.

GB
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
URY914
post May 17 2006, 08:25 AM
Post #4


I built the lightest 914 in the history of mankind.
****************************************************************************************************

Group: Members
Posts: 123,987
Joined: 3-February 03
From: Jacksonville, FL
Member No.: 222
Region Association: None
Mine get so tight sometimes I have to.....wait you mean trailing arm nuts?

Yea mine do get loose too. I think it has to do with after market bushings and the shaft. If the shaft and bushings are not centered in relation to the trailing are shaft tube you can't tighten the nut down until it seats at the bottom of the threads. I least that's what I'm thinkin'. Could be wrong.
User is online!Profile CardPM
Go to the top of the page
+Quote Post
GBallantine
post May 17 2006, 08:32 AM
Post #5


Member
**

Group: Members
Posts: 74
Joined: 12-October 04
From: Toronto,Ont.Canada
Member No.: 2,930
When I was at Hershey this April the fellow from Air Cooled Racing showed me an improved trailing arm shaft. It looked to be a bit longer and stronger. Not sure how much they were.

GB
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
John
post May 17 2006, 09:00 AM
Post #6


member? what's a member?
****

Group: Members
Posts: 3,393
Joined: 30-January 04
From: Evansville, IN (SIRPCA)
Member No.: 1,615
Region Association: None
My theory is that the nuts loosen due to the shaft rotating.

I think the shaft rotates because the plastic bushings are too thick and don't allow the serrated ends of the shaft to 'bite' into the mounts like they should. I have faced the outer ends of my plastic bushings slightly to allow the ends of the shafts to contact the mount locations.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
vesnyder
post May 17 2006, 09:19 AM
Post #7


Senior Member
***

Group: Members
Posts: 680
Joined: 14-April 05
From: Cleveland, OH
Member No.: 3,933
Anybody tried Loc-Tite - seems like a logical application? Mine are apart and I know I will have similar issues!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
URY914
post May 17 2006, 09:20 AM
Post #8


I built the lightest 914 in the history of mankind.
****************************************************************************************************

Group: Members
Posts: 123,987
Joined: 3-February 03
From: Jacksonville, FL
Member No.: 222
Region Association: None
QUOTE(JOHNMAN @ May 17 2006, 07:00 AM) *

My theory is that the nuts loosen due to the shaft rotating.

I think the shaft rotates because the plastic bushings are too thick and don't allow the serrated ends of the shaft to 'bite' into the mounts like they should. I have faced the outer ends of my plastic bushings slightly to allow the ends of the shafts to contact the mount locations.


I agree with you. The end "flange" for lack of a better term on the bushings are too thick.
User is online!Profile CardPM
Go to the top of the page
+Quote Post
root
post May 17 2006, 12:42 PM
Post #9


Two Wheeled Type4 Completed!
***

Group: Members
Posts: 849
Joined: 5-May 04
From: Sterling, VA
Member No.: 2,026
Region Association: None
O.K. I have new delrin bushings installed and seems like I remember they stuck out a bit beyond the seration on the pivot rod end. At the time I figured knuckling down on the nut would be enough to catch the serations? Here's what it looked like;


Attached thumbnail(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
root
post May 17 2006, 12:55 PM
Post #10


Two Wheeled Type4 Completed!
***

Group: Members
Posts: 849
Joined: 5-May 04
From: Sterling, VA
Member No.: 2,026
Region Association: None
Pressing in the bushings. I used polycarbonate tube peices so I could see the
bushings seat;


Attached thumbnail(s)
Attached Image

Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Andyrew
post May 17 2006, 12:58 PM
Post #11


Spooling.... Please wait
**********

Group: Members
Posts: 13,377
Joined: 20-January 03
From: Riverbank, Ca
Member No.: 172
Region Association: Northern California
I have the same problem.

Hopefully roller bearings will solve it.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
root
post May 17 2006, 01:05 PM
Post #12


Two Wheeled Type4 Completed!
***

Group: Members
Posts: 849
Joined: 5-May 04
From: Sterling, VA
Member No.: 2,026
Region Association: None
Who's the roller bearing guy in the club? I know someone was working on it! (IMG:style_emoticons/default/idea.gif)

Does anyone know the thread size of the trailing arm nut off-hand. Help me avoid looking it up or measuring it....... (IMG:style_emoticons/default/boldblue.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
brant
post May 17 2006, 03:40 PM
Post #13


914 Wizard
**********

Group: Members
Posts: 11,801
Joined: 30-December 02
From: Colorado
Member No.: 47
Region Association: Rocky Mountains
I hope you all know the reason for these nuts to come loose.

I promise you its due to chassis flex

Its a commone occurance on track cars.

you will someday go around a track corner and suddenly rip a CV apart (from stretching)

as you are wondering why or how that could of happened you will notice a big crack in your suspension console.

most likely the right side one.

I know this..
I lived it.
I used to tighen these (inboard and outboard) EVERY single track day for 8+ years

Then I ripped my console out.
replaced it with fresh.. brand new console.
continued tightening those nuts every single day for 6 more months.
then ripped out my 2nd console.

Thats when I learned about the need for a swing arm brace.
Haven't had a single swing arm nut come loose in the 10 years that I've used bracing. Even with 2 drivers doing wheel to wheel club racing.

I use bolt in bracing with aluminum bars.
doesn't weigh much.
comes out easily enough for dropping the motors.

the arm causes side to side flex at the console.
sometimes the console will oval out first
sometimes not..

eventually you will get to enjoy the same fun experience I have.
brant
User is online!Profile CardPM
Go to the top of the page
+Quote Post
Andyrew
post May 17 2006, 03:57 PM
Post #14


Spooling.... Please wait
**********

Group: Members
Posts: 13,377
Joined: 20-January 03
From: Riverbank, Ca
Member No.: 172
Region Association: Northern California
Pictures please brant.

I have it come loose from driving about 4 blocks....

I think its a combination of a few things..
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
brant
post May 17 2006, 04:02 PM
Post #15


914 Wizard
**********

Group: Members
Posts: 11,801
Joined: 30-December 02
From: Colorado
Member No.: 47
Region Association: Rocky Mountains
my -4 cylinder version is smaller and less intrusive.
but here is the basic idea:


Attached thumbnail(s)
Attached Image
User is online!Profile CardPM
Go to the top of the page
+Quote Post
wbergtho
post May 17 2006, 04:22 PM
Post #16


Senior Member
***

Group: Members
Posts: 1,314
Joined: 28-April 03
From: Roberts, WI
Member No.: 623
I have had two real freaky occurances when the traing arm nuts loosened. I nailed it in a straight line and the car darted first to the right...then left...and I almost lost control of the car for about 1-2 seconds (long enough to do serious damage or die). I then checked everything and found that the inner trailng arm nuts were loose as a goose causing a sloppy toe in/out vasilation. It happened again just a week ago and the fu___g nuts were loose again! after red lock tight. I like the bearing idea...but I think I'll go to castle nuts and drill & pin the stupid things so they don't kill me. What are your collective thoughts on that idea. It certainly would put an end to the inners loosening...but I'm afraid I had better do both sides...

Bill
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Andyrew
post May 17 2006, 05:17 PM
Post #17


Spooling.... Please wait
**********

Group: Members
Posts: 13,377
Joined: 20-January 03
From: Riverbank, Ca
Member No.: 172
Region Association: Northern California
Ahh that piece brant.

I thought you have a piece that attached to the actual body, and then to the outside nut. Holding it from moving forward to back (getting rid of toe change)

Andrew.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
brant
post May 17 2006, 09:14 PM
Post #18


914 Wizard
**********

Group: Members
Posts: 11,801
Joined: 30-December 02
From: Colorado
Member No.: 47
Region Association: Rocky Mountains
I have the toe change brace too...
but that is not the reason your swing arm mounts are coming loose.

its the inner one that flexes and allow's the loosening....

look under the chassis some time.
the frame is straight down the longs.
but when it gets to the swingarm mount it turns sharply.

a TON of leverage is being applied (side to side) on that single bolt.
its the inner one that flexes....

by triangulating the inner one to the firewall you are adding LOTS of strength and bracing....

no one believes me... thats fine.
I like being faster and right.
wait until you have all dealt with a ripped console and then you will reconsider.

the nut comes loose from flex.

(10 years of reality testing proves it... Plus my guru has proven it on 15 other cars)
User is online!Profile CardPM
Go to the top of the page
+Quote Post
Brad Roberts
post May 17 2006, 10:18 PM
Post #19


914 Freak!
***************

Group: Members
Posts: 19,148
Joined: 23-December 02
Member No.: 8
Region Association: None
QUOTE
I think the shaft rotates because the plastic bushings are too thick and don't allow the serrated ends of the shaft to 'bite' into the mounts like they should. I have faced the outer ends of my plastic bushings slightly to allow the ends of the shafts to contact the mount locations.



This is the only reason. We figured this out 20 years ago when we cut our first bushings. The serated ends HAVE to lock into the ear and the outer cup. If the bushings dont collaspe like the stock rubber when torquing the nuts down.. they will come loose. The shaft is NOT designed to pivot in the mounts.

That being said: I shave all the plasic bushings until the serrated ends hang past the bushings. Problem solved.

You should still check them AND the inner mount every event. Also make sure your drains are clean on the bottom of the inside mount.


B
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mueller
post May 17 2006, 11:33 PM
Post #20


914 Freak!
***************

Group: Members
Posts: 17,150
Joined: 4-January 03
From: Antioch, CA
Member No.: 87
Region Association: None
pretty much what Brad said....

for the roller bearings, the shaft sticks out past the trust washer by about .001" to .002" per side

(IMG:http://muellerdesignwerks.com/TAB-endview-closeup1.jpg)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

2 Pages V  1 2 >
Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Standard · Switch to: Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 28th November 2024 - 06:37 PM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...