 Axles for Subaru Conversion, 914 hubs ok? Where to get the work done? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| Corkus |
 Jul 28 2010, 05:19 PM
Post
#1
|
|
Newbie  Group: Members Posts: 22 Joined: 14-June 10 From: N. Calif & S. AZ Member No.: 11,834 Region Association: None  |
Currently have:
2000 Subaru Legacy donor car EJ25 165 hp/165 foot-lbs torque engine Subaru axles 914 Hubs 4 lug wheels 914 CV Joints Bremar Kit installed Questions: Am I ok with the 4 lug wheels and 914 hubs? Are they strong enough for this drivetrain assuming I don't modify it for more power? I had Riveria wheels on my 914 in the 70's and kind of want them on this car if they are strong enough. I am expecting to take those long Subaru axles to a machine shop and have the outboard ends machined to accept 914 CV's/hubs. Am I right? And where do I get this kind of machine work done? Any suggestions? Thanks all. |
   |
 
|
| 1968Cayman |
Jul 28 2010, 08:18 PM
Post
#2
|
|
Redacted by Irving Washington Group: Members Posts: 116 Joined: 5-February 10 From: Holly Springs, GA Member No.: 11,332 Region Association: South East States |
I'm having mine sent to Dutchman Motorsports. Using everything you're suggesting.
|
|
|
|
| BIGKAT_83 |
Jul 28 2010, 08:37 PM
Post
#3
|
|
Senior Member Group: Members Posts: 1,798 Joined: 25-January 03 From: Way down south Bogart,GA Member No.: 194 Region Association: South East States 
|
QUOTE(1968Cayman @ Jul 28 2010, 10:18 PM)  I'm having mine sent to Dutchman Motorsports. Using everything you're suggesting. Had Dutchman do the work for me also. I used 911 axles and had them cut for the subaru inter CV. The 911 axles are far bigger diameter than the subaru axles. I have also found a shop in the Atlanta area that can do the work at about half the price Attached image(s) 
|
|
|
|
| 1968Cayman |
Jul 29 2010, 12:40 PM
Post
#4
|
|
Redacted by Irving Washington Group: Members Posts: 116 Joined: 5-February 10 From: Holly Springs, GA Member No.: 11,332 Region Association: South East States |
I'm in the Atlanta area- do tell!! Who can do the work?
|
|
|
|
| nsyr |
Jul 29 2010, 12:41 PM
Post
#5
|
|
Because I Can Group: Members Posts: 314 Joined: 16-May 04 From: Tampa, FL Member No.: 2,073 |
what is the cost for something like this?
|
|
|
|
| 1968Cayman |
Jul 29 2010, 06:11 PM
Post
#6
|
|
Redacted by Irving Washington Group: Members Posts: 116 Joined: 5-February 10 From: Holly Springs, GA Member No.: 11,332 Region Association: South East States |
Think I'm paying $125 for the machine work to both axles.
|
|
|
|
| charliew |
Aug 10 2010, 05:36 PM
Post
#7
|
|
Advanced Member Group: Members Posts: 2,363 Joined: 31-July 07 From: Crawford, TX. Member No.: 7,958 |
I assume by both axles as in suby axles or have you switched to 911 axles?
|
|
|
|
|
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 23rd November 2024 - 11:22 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.