Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

2 Pages V  1 2 >  
 Reply to this topicStart new topic
> Fuel Pump will not run, Checked fuse, relay, etc
BCinSC
post May 29 2011, 08:42 AM
Post #1


Nothing but Trouble
**

Group: Members
Posts: 138
Joined: 8-June 03
From: Wakefield, MA
Member No.: 800
Region Association: North East States
So Blanche ('73 White 914-4 1.7L) was running great last summer until she simply stopped on I-95 in Burlington, MA. Simply no spark anymore. Having no time to deal with it, she sat until today. I figured out the spark problem, but now the fuel pump, won't. Familiar with this type of issue, I open the relay board and check the fuse and the relay. I've got 12V where I'm suppose to - both sides of fuse, pin85 of FP relay when key on (FI Brain energizes to close circuit to join pin30 and pin87 I believe). PIN13 of connector closest to firewall, which diagram says goes out to FP itself, shows continuity to ground, so I'm guessing broken wire somewhere. Sounds reasonable/plausible? Fuel Pump was functional before I put her away.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
SLITS
post May 29 2011, 09:05 AM
Post #2


"This Utah shit is HARSH!"
**********

Group: Benefactors
Posts: 13,602
Joined: 22-February 04
From: SoCal Mountains ...
Member No.: 1,696
Region Association: None
Pumps do gum up or fail.

Run hot wire to + terminal and another to ground and see if the pump will run at all as a test. If it does, go from there with the tracing of wires.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BCinSC
post May 29 2011, 09:12 AM
Post #3


Nothing but Trouble
**

Group: Members
Posts: 138
Joined: 8-June 03
From: Wakefield, MA
Member No.: 800
Region Association: North East States
Is that Gumby with a Blunt? Anyway, I think you are correct that the pump has failed. It has continuity through it and I don't think it should. Another one I have that I believe is good, does not have continuity. I will check both as you suggest.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Tom
post May 29 2011, 09:12 AM
Post #4


Advanced Member
****

Group: Members
Posts: 2,139
Joined: 21-August 05
From: Port Orchard, WA 98367
Member No.: 4,626
Region Association: None
Bruce,
Just went thru this yesterday with another member.
1- with the fuel pump relay removed, jump pin 13 and 14 of the 14 pin connector. Pin 14 is always hot, so you don't need the key on. If the pump runs, the pump and wiring are good, and the problem is in the relay board somewhere - most likely ( I can never be 100% sure with these cars). If pump does not run, check with voltmeter to ensure 12 Volts at pin 14. This comes from the batt +, one of the 4 large red wires attached at the batt. If the voltage is present, then you have a wiring or fuel pump problem.
Let me know what you find and we can go from there to find the problem.
Tom
PS; you will continuity thru the pump brushes to ground, don't let that throw ya.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Elliot Cannon
post May 29 2011, 09:13 AM
Post #5


914 Guru
*****

Group: Retired Members
Posts: 8,487
Joined: 29-December 06
From: Paso Robles Ca. (Central coast)
Member No.: 7,407
Region Association: None
QUOTE(SLITS @ May 29 2011, 08:05 AM) *

Pumps do gum up or fail.

Run hot wire to + terminal and another to ground and see if the pump will run at all as a test. If it does, go from there with the tracing of wires.


I agree with Ron? (IMG:style_emoticons/default/agree.gif) I had the same problem with the Zonker. Twice!! Hot wired a spare battery to the pump and it DIDN'T run. Very quick trouble shooting. (I guess the old geezer DOES know what he's talking about). (IMG:style_emoticons/default/lol-2.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
SLITS
post May 29 2011, 09:37 AM
Post #6


"This Utah shit is HARSH!"
**********

Group: Benefactors
Posts: 13,602
Joined: 22-February 04
From: SoCal Mountains ...
Member No.: 1,696
Region Association: None
QUOTE(Elliot Cannon @ May 29 2011, 08:13 AM) *

QUOTE(SLITS @ May 29 2011, 08:05 AM) *

Pumps do gum up or fail.

Run hot wire to + terminal and another to ground and see if the pump will run at all as a test. If it does, go from there with the tracing of wires.


I agree with Ron? (IMG:style_emoticons/default/agree.gif) I had the same problem with the Zonker. Twice!! Hot wired a spare battery to the pump and it DIDN'T run. Very quick trouble shooting. (I guess the old geezer DOES know what he's talking about). (IMG:style_emoticons/default/lol-2.gif)


I do have my "senior" moments, especially with a blunt. (IMG:style_emoticons/default/confused24.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BCinSC
post May 29 2011, 10:11 AM
Post #7


Nothing but Trouble
**

Group: Members
Posts: 138
Joined: 8-June 03
From: Wakefield, MA
Member No.: 800
Region Association: North East States
Argh. Swapped pumps and same deal. Could FI Brain be disabling somehow? Wiring seems good and both pumps function while connected directly to 12V. Jumping 13 and 14 as you suggest DOES run pump (but I shouldn't let it for more than a couple seconds, right?)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
SLITS
post May 29 2011, 10:16 AM
Post #8


"This Utah shit is HARSH!"
**********

Group: Benefactors
Posts: 13,602
Joined: 22-February 04
From: SoCal Mountains ...
Member No.: 1,696
Region Association: None
QUOTE(BCinSC @ May 29 2011, 09:11 AM) *

Argh. Swapped pumps and same deal. Could FI Brain be disabling somehow? Wiring seems good and both pumps function while connected directly to 12V. Jumping 13 and 14 as you suggest DOES run pump (but I shouldn't let it for more than a couple seconds, right?)



As long as you have fuel flowing thru the system, you can run it as long as you want. Fuel cools the motor on the pump. Dry .... not so good as it will overheat and kill the pump.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BCinSC
post May 29 2011, 10:26 AM
Post #9


Nothing but Trouble
**

Group: Members
Posts: 138
Joined: 8-June 03
From: Wakefield, MA
Member No.: 800
Region Association: North East States
I don't get it. I have 12V at Pin30 of Relay. I have continuity from Relay Pin87 socket to harness PIN13. I can run the pump jumping harness 13 and 14. I have checked the relays and swapped with spares. What am I missing?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BCinSC
post May 29 2011, 10:34 AM
Post #10


Nothing but Trouble
**

Group: Members
Posts: 138
Joined: 8-June 03
From: Wakefield, MA
Member No.: 800
Region Association: North East States
Mess with it long enough, and miraculously, it will work. Pump now functional (not exactly sure why, but not complaining). So now I have crank and gas, how does one person check that spark it working?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Tom
post May 29 2011, 10:51 AM
Post #11


Advanced Member
****

Group: Members
Posts: 2,139
Joined: 21-August 05
From: Port Orchard, WA 98367
Member No.: 4,626
Region Association: None
The relays sometimes don't fit tight in the socket. The pins can be spread slightly to get a better fit. Sounds like you had an intermittent relay connection.
As for spark, pull one plug wire and put an old plug or screwdriver in the plug wire. Hold the spark plug to ground or screwdriver close to ground and crank. You should see a spark from the spark plug or from screwdriver to ground.
Tom
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BCinSC
post May 29 2011, 12:09 PM
Post #12


Nothing but Trouble
**

Group: Members
Posts: 138
Joined: 8-June 03
From: Wakefield, MA
Member No.: 800
Region Association: North East States
Not quite the contortionist I used to be. Can't seem to manage turning key to crank and holding plug lead to screwdriver to ground point all at same time. Did hookup strobe and don't see it flicker, so maybe that's something?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BCinSC
post May 29 2011, 12:17 PM
Post #13


Nothing but Trouble
**

Group: Members
Posts: 138
Joined: 8-June 03
From: Wakefield, MA
Member No.: 800
Region Association: North East States
Hooked up known good spark plug to wire #1 and cranked. No spark. Back to square one. Suggestions?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
benalishhero
post May 29 2011, 01:03 PM
Post #14


Member
**

Group: Members
Posts: 313
Joined: 28-November 07
From: Portland, Maine
Member No.: 8,384
Region Association: North East States
No spark? Are you running points and condensor?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BCinSC
post May 29 2011, 01:34 PM
Post #15


Nothing but Trouble
**

Group: Members
Posts: 138
Joined: 8-June 03
From: Wakefield, MA
Member No.: 800
Region Association: North East States
Yes. Both relatively new (couple thousand miles at most). Checked the points, which appear to be functioning correctly (at least they open and close as crank turns)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BCinSC
post May 29 2011, 01:36 PM
Post #16


Nothing but Trouble
**

Group: Members
Posts: 138
Joined: 8-June 03
From: Wakefield, MA
Member No.: 800
Region Association: North East States
I reiterate that I was doing 60+ on the highway when she died. Tach just went to zero and no more power. Coasted to shoulder, where she would crank, but not catch. Same today.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Elliot Cannon
post May 29 2011, 01:38 PM
Post #17


914 Guru
*****

Group: Retired Members
Posts: 8,487
Joined: 29-December 06
From: Paso Robles Ca. (Central coast)
Member No.: 7,407
Region Association: None
QUOTE(SLITS @ May 29 2011, 08:37 AM) *

QUOTE(Elliot Cannon @ May 29 2011, 08:13 AM) *

QUOTE(SLITS @ May 29 2011, 08:05 AM) *

Pumps do gum up or fail.

Run hot wire to + terminal and another to ground and see if the pump will run at all as a test. If it does, go from there with the tracing of wires.


I agree with Ron? (IMG:style_emoticons/default/agree.gif) I had the same problem with the Zonker. Twice!! Hot wired a spare battery to the pump and it DIDN'T run. Very quick trouble shooting. (I guess the old geezer DOES know what he's talking about). (IMG:style_emoticons/default/lol-2.gif)


I do have my "senior" moments, especially with a blunt. (IMG:style_emoticons/default/confused24.gif)


Gosh!! What's a blunt?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Elliot Cannon
post May 29 2011, 01:42 PM
Post #18


914 Guru
*****

Group: Retired Members
Posts: 8,487
Joined: 29-December 06
From: Paso Robles Ca. (Central coast)
Member No.: 7,407
Region Association: None
I just had a crap load of electrical problems with both cars and it turned out to be mostly corrosion. Roll up some sand paper, stick it down the holes for the relays and clean, clean, clean. It seems like I spend a lot of time looking for and controlling body rust and not enough time cleaning up electrical contact corrosion.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BCinSC
post May 29 2011, 02:59 PM
Post #19


Nothing but Trouble
**

Group: Members
Posts: 138
Joined: 8-June 03
From: Wakefield, MA
Member No.: 800
Region Association: North East States
Checked points more closely and found that the metal (copper?) piece within the points arm that the dizzy pushes against was 98% broken and that the points really weren't separating at all. Fortunately, FLAPS should have in stock. Maybe she'll light up later today!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
djm914-6
post May 29 2011, 03:08 PM
Post #20


Happiness is: Getting on the road
***

Group: Members
Posts: 1,864
Joined: 6-February 03
From: Burlington MA
Member No.: 248
Region Association: None
Sounds like you're having fun. WHo's watching the two kids, 8 dogs and the cat?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

2 Pages V  1 2 >
Reply to this topicStart new topic
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Standard · Switch to: Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 26th December 2024 - 01:24 PM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...