Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

 
 Reply to this topicStart new topic
> Fan Shroud, Are you supposed to be able to seperate it?
Vicious
post Apr 1 2025, 01:13 PM
Post #1


Newbie
*

Group: Members
Posts: 36
Joined: 31-October 22
From: South Dakota, USA
Member No.: 26,958
Region Association: Upper MidWest
My fan shroud in some spots looks like it's separating. I'd like to fully seperate it and get it cleaned up and powder coated/ painted in and out. I don't see any fasteners holding it together though
User is online!Profile CardPM
Go to the top of the page
+Quote Post
Geezer914
post Apr 1 2025, 01:30 PM
Post #2


Geezer914
***

Group: Members
Posts: 1,889
Joined: 18-March 09
From: Salem, NJ
Member No.: 10,179
Region Association: North East States
Should be screws holding it together.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
930cabman
post Apr 1 2025, 02:15 PM
Post #3


Advanced Member
****

Group: Members
Posts: 4,005
Joined: 12-November 20
From: Buffalo
Member No.: 24,877
Region Association: North East States
QUOTE(Geezer914 @ Apr 1 2025, 01:30 PM) *

Should be screws holding it together.


also a couple steel dowels, often get stuck there
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
mepstein
post Apr 1 2025, 02:19 PM
Post #4


914-6 GT in waiting
***************

Group: Members
Posts: 19,811
Joined: 19-September 09
From: Landenberg, PA/Wilmington, DE
Member No.: 10,825
Region Association: MidAtlantic Region
It's balanced so make some witness marks so it goes together the same way.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Vicious
post Apr 1 2025, 03:14 PM
Post #5


Newbie
*

Group: Members
Posts: 36
Joined: 31-October 22
From: South Dakota, USA
Member No.: 26,958
Region Association: Upper MidWest
QUOTE(Geezer914 @ Apr 1 2025, 02:30 PM) *

Should be screws holding it together.


There was in fact no screws holding the shroud together. One of many things I've found that show me that the shop the previous owner had put this thing together were idiots. The alternator was the only thing holding this thing together. I will need to source some replacement screws while it's at the powder coater
User is online!Profile CardPM
Go to the top of the page
+Quote Post
brant
post Apr 1 2025, 04:07 PM
Post #6


914 Wizard
**********

Group: Members
Posts: 11,926
Joined: 30-December 02
From: Colorado
Member No.: 47
Region Association: Rocky Mountains
maybe balancing it when you reassemble.
it rotates pretty high speed at high RPM
worth doing.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Vicious
post Apr 1 2025, 05:32 PM
Post #7


Newbie
*

Group: Members
Posts: 36
Joined: 31-October 22
From: South Dakota, USA
Member No.: 26,958
Region Association: Upper MidWest
QUOTE(brant @ Apr 1 2025, 05:07 PM) *

maybe balancing it when you reassemble.
it rotates pretty high speed at high RPM
worth doing.


I was wondering about the balancing comment above. Now I'm realizing i must be using the wrong verbiage. This is the piece I'm talking about. The two halves were not fastened together and after removing the alternator were able to be separated. If anyone knows what the correct size fastener is I'd be very grateful.


Attached thumbnail(s)
Attached Image
User is online!Profile CardPM
Go to the top of the page
+Quote Post
Ron914
post Apr 1 2025, 05:45 PM
Post #8


Member
**

Group: Members
Posts: 181
Joined: 19-April 22
From: Huntington Beach,Ca
Member No.: 26,487
Region Association: Southern California
QUOTE(Vicious @ Apr 1 2025, 06:32 PM) *

QUOTE(brant @ Apr 1 2025, 05:07 PM) *

maybe balancing it when you reassemble.
it rotates pretty high speed at high RPM
worth doing.


I was wondering about the balancing comment above. Now I'm realizing i must be using the wrong verbiage. This is the piece I'm talking about. The two halves were not fastened together and after removing the alternator were able to be separated. If anyone knows what the correct size fastener is I'd be very grateful.

I was wondering about the comments on this ,only the fan wheel itself turns certainly the shroud doesn't rotate .
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Ron914
post Apr 1 2025, 05:47 PM
Post #9


Member
**

Group: Members
Posts: 181
Joined: 19-April 22
From: Huntington Beach,Ca
Member No.: 26,487
Region Association: Southern California
QUOTE(Ron914 @ Apr 1 2025, 06:45 PM) *

QUOTE(Vicious @ Apr 1 2025, 06:32 PM) *

QUOTE(brant @ Apr 1 2025, 05:07 PM) *

maybe balancing it when you reassemble.
it rotates pretty high speed at high RPM
worth doing.


I was wondering about the balancing comment above. Now I'm realizing i must be using the wrong verbiage. This is the piece I'm talking about. The two halves were not fastened together and after removing the alternator were able to be separated. If anyone knows what the correct size fastener is I'd be very grateful.

I was wondering about the comments on this ,only the fan wheel itself turns certainly the shroud doesn't rotate .

While working on my motor during reassembly I tried to split the halves of the shroud but it didn't bug so I decided leave it alone before I break it.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bkrantz
post Apr 1 2025, 07:53 PM
Post #10


914 Guru
*****

Group: Members
Posts: 8,320
Joined: 3-August 19
From: SW Colorado
Member No.: 23,343
Region Association: Rocky Mountains
QUOTE(Vicious @ Apr 1 2025, 05:32 PM) *

QUOTE(brant @ Apr 1 2025, 05:07 PM) *

maybe balancing it when you reassemble.
it rotates pretty high speed at high RPM
worth doing.


I was wondering about the balancing comment above. Now I'm realizing i must be using the wrong verbiage. This is the piece I'm talking about. The two halves were not fastened together and after removing the alternator were able to be separated. If anyone knows what the correct size fastener is I'd be very grateful.


Off the top of my head, it uses a couple of different thread sizes and lengths. I replaced the stock bolts with stainless Allen heads.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bdstone914
post Apr 1 2025, 08:00 PM
Post #11


bdstone914
****

Group: Members
Posts: 4,848
Joined: 8-November 03
From: Riverside CA
Member No.: 1,319
QUOTE(Vicious @ Apr 1 2025, 02:14 PM) *

QUOTE(Geezer914 @ Apr 1 2025, 02:30 PM) *

Should be screws holding it together.


There was in fact no screws holding the shroud together. One of many things I've found that show me that the shop the previous owner had put this thing together were idiots. The alternator was the only thing holding this thing together. I will need to source some replacement screws while it's at the powder coater


Look up the sizes in PET. Several 6mm by about 30mm and a few 8mm hex bolts
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Vicious
post Apr 1 2025, 08:12 PM
Post #12


Newbie
*

Group: Members
Posts: 36
Joined: 31-October 22
From: South Dakota, USA
Member No.: 26,958
Region Association: Upper MidWest
QUOTE(bdstone914 @ Apr 1 2025, 09:00 PM) *

QUOTE(Vicious @ Apr 1 2025, 02:14 PM) *

QUOTE(Geezer914 @ Apr 1 2025, 02:30 PM) *

Should be screws holding it together.


There was in fact no screws holding the shroud together. One of many things I've found that show me that the shop the previous owner had put this thing together were idiots. The alternator was the only thing holding this thing together. I will need to source some replacement screws while it's at the powder coater


Look up the sizes in PET. Several 6mm by about 30mm and a few 8mm hex bolts


I'm sorry but still A LOT i don't know...what is PET?
User is online!Profile CardPM
Go to the top of the page
+Quote Post
JeffBowlsby
post Apr 1 2025, 10:35 PM
Post #13


914 Wiring Harnesses & Beekeeper
*****

Group: Members
Posts: 8,872
Joined: 7-January 03
From: San Ramon CA
Member No.: 104
Region Association: None
Here is a copy:

https://bowlsby.net/914/Classic/zTN_Man01C.pdf
User is online!Profile CardPM
Go to the top of the page
+Quote Post
Mikey914
post Apr 1 2025, 11:38 PM
Post #14


The rubber man
**********

Group: Members
Posts: 12,761
Joined: 27-December 04
From: Hillsboro, OR
Member No.: 3,348
Region Association: None
I've got them, hit me up and I'll drop them in the mail.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
brant
post Apr 2 2025, 05:47 AM
Post #15


914 Wizard
**********

Group: Members
Posts: 11,926
Joined: 30-December 02
From: Colorado
Member No.: 47
Region Association: Rocky Mountains
My mistake
Misunderstood
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Vicious
post Apr 2 2025, 05:58 AM
Post #16


Newbie
*

Group: Members
Posts: 36
Joined: 31-October 22
From: South Dakota, USA
Member No.: 26,958
Region Association: Upper MidWest
QUOTE(Mikey914 @ Apr 2 2025, 12:38 AM) *

I've got them, hit me up and I'll drop them in the mail.


My hero
User is online!Profile CardPM
Go to the top of the page
+Quote Post
73-914
post Apr 2 2025, 07:15 AM
Post #17


Senior Member
***

Group: Members
Posts: 610
Joined: 24-April 10
From: Albany UpstateNY
Member No.: 11,651
Region Association: None
QUOTE(mepstein @ Apr 1 2025, 04:19 PM) *

It's balanced so make some witness marks so it goes together the same way.

(IMG:style_emoticons/default/screwy.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
mgphoto
post Apr 2 2025, 05:54 PM
Post #18


"If there is a mistake it will find me"
***

Group: Members
Posts: 1,374
Joined: 1-April 09
From: Los Angeles, CA
Member No.: 10,225
Region Association: Southern California
Fan needs to be balanced, if you take it apart, not the shroud, I needed to take mine apart to clean the grease out of it before powder coating. A bit tough to separate but it can be done.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

Reply to this topicStart new topic
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Standard · Switch to: Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 3rd April 2025 - 05:53 PM
Invision Power Board v9.1.4 © 2025  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...