Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

 
 Reply to this topicStart new topic
> G50 (or any tranny) flip, Turning a tranny upside down
jc87930
post Aug 31 2003, 10:21 PM
Post #1


Newbie
*

Group: Members
Posts: 6
Joined: 31-August 03
From: Victoria, BC
Member No.: 1,093
Hi everyone! I have a tube frame 914 that I'm putting a 993 3.6 in and a G50 trans to go with it. I have read lots of old threads on NOT flipping the G50 for use in a 914 but was hoping for some advice.

I understand that flipping the diff is just too hard and have heard that to flip the entire trans requires cutting bell housings off etc.

My question is, why can I not simply fill the old holes, build up the case a bit, and drill new holes? They only need to move 1/4".

Jim
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Brad Roberts
post Sep 1 2003, 01:02 AM
Post #2


914 Freak!
***************

Group: Members
Posts: 19,148
Joined: 23-December 02
Member No.: 8
Region Association: None
Hey Jim.

I was "forewarned" that you where heading this way from Rennlist.

Do exactly like your thinking and fill the current holes and redrill.

Typically we shorten the bellhousing also... if you dont ..then end of the tranny ends up almost hanging out the back of the car (even with your Sheridan body kit).

The other thing you need to do.. equalize the gear lube. Run a line from the diff area to the nosecone. If you dont .. more of the gear lube will sit in the nose cone area than in the diff area.

Remind me later.. and I will show you a pic of one upside down.

B
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Jeroen
post Sep 1 2003, 03:47 AM
Post #3


914 Guru
*****

Group: Members
Posts: 7,887
Joined: 24-December 02
From: The Netherlands
Member No.: 3
Region Association: Europe
Hey Jim,

Good to see you made it here.
Welcome aboard...

cheers,

Jeroen
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
jc87930
post Sep 1 2003, 06:05 PM
Post #4


Newbie
*

Group: Members
Posts: 6
Joined: 31-August 03
From: Victoria, BC
Member No.: 1,093
Thanks guys!

Nice to E-meet you Brad! Ok, one more little idea, since the starter shares one of the studs I thought why not leave that one alone? And it so happens that the upper right stud and the starter stud still line up!

So my idea is to leave the two right hand studs as they are AND get this, it is easier to ADD two new studs to the engine (IMG:style_emoticons/default/ar15.gif) than even touch the trans! The 993 has room, I just need to build up a little area for each stud cuz the case has recesses just behind where the stud pokes through.

The only issue I see is that the tranny will be a few degrees off of level. So I will just mount the engine a little bit the other way. I figure that the back and forth of a race will negate any problems. Besides, my fat ass tips the car over anyway!

What do ya think!

Thanks,

Jim
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Bleyseng
post Sep 1 2003, 09:55 PM
Post #5


Aircooled Baby!
**********

Group: Members
Posts: 13,036
Joined: 27-December 02
From: Seattle, Washington (for now)
Member No.: 24
Region Association: Pacific Northwest
Where do you race in Victoria,BC?
Love going up there and enjoying the harbor and Chinatown..
Can't help you at all with the G50...

Geoff
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
MarkV
post Sep 1 2003, 10:19 PM
Post #6


Fear the Jack Stands
***

Group: Members
Posts: 1,493
Joined: 15-January 03
From: Sunny Tucson, AZ
Member No.: 154
Region Association: None
Did anyone notice this:

http://cgi.ebay.com/ebaymotors/ws/eBayISAP...&category=33733


Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
jc87930
post Sep 1 2003, 11:43 PM
Post #7


Newbie
*

Group: Members
Posts: 6
Joined: 31-August 03
From: Victoria, BC
Member No.: 1,093
Hey Geoff,

We autocross at a local circle track call Western Speedway, and several large parking lots in town.

Thanks for the ebay link Mark, nice tranny, I would definately go there if I did not have the G50.

I have made a temporary stud (needs welding around it for strength) and bolted the trans on. And am fitting in the car now.

Jim
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
jc87930
post Sep 1 2003, 11:48 PM
Post #8


Newbie
*

Group: Members
Posts: 6
Joined: 31-August 03
From: Victoria, BC
Member No.: 1,093
Attempt at attaching an image...


Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
redshift
post Sep 1 2003, 11:59 PM
Post #9


Bless the Hell out of you!
**********

Group: Members
Posts: 10,926
Joined: 29-June 03
Member No.: 869
QUOTE(MarkV @ Sep 2 2003, 12:19 AM)
Did anyone notice this:

http://cgi.ebay.com/ebaymotors/ws/eBayISAP...&category=33733

3:10? Holy Cow.



M
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Brad Roberts
post Sep 2 2003, 12:29 AM
Post #10


914 Freak!
***************

Group: Members
Posts: 19,148
Joined: 23-December 02
Member No.: 8
Region Association: None
Um.. Jim.. That is a C4 tranny out of an all wheel drive car.

How do you plan to cap the end ??


B
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Bleyseng
post Sep 2 2003, 06:20 AM
Post #11


Aircooled Baby!
**********

Group: Members
Posts: 13,036
Joined: 27-December 02
From: Seattle, Washington (for now)
Member No.: 24
Region Association: Pacific Northwest
Here we go! an all wheel drive 914! should be great for AXing. Look out JP!


Geoff
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
redshift
post Sep 2 2003, 06:41 AM
Post #12


Bless the Hell out of you!
**********

Group: Members
Posts: 10,926
Joined: 29-June 03
Member No.: 869
QUOTE(Brad Roberts @ Sep 2 2003, 02:29 AM)
How do you plan to cap the end ??

B

With a prop?



M
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
jc87930
post Sep 2 2003, 04:49 PM
Post #13


Newbie
*

Group: Members
Posts: 6
Joined: 31-August 03
From: Victoria, BC
Member No.: 1,093
Lol, a prop, good one! Maybe a PTO for a winch?

Knew that would spark some comments!

No, the transfer case just unbolts. I am going to make an integrated cap/mount. (IMG:style_emoticons/default/smile.gif)

Jim
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mueller
post Sep 2 2003, 05:13 PM
Post #14


914 Freak!
***************

Group: Members
Posts: 17,150
Joined: 4-January 03
From: Antioch, CA
Member No.: 87
Region Association: None
I see an AWD 914 in future (IMG:style_emoticons/default/smile.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Dave_Darling
post Sep 2 2003, 05:17 PM
Post #15


914 Idiot
***************

Group: Members
Posts: 15,062
Joined: 9-January 03
From: Silicon Valley / Kailua-Kona
Member No.: 121
Region Association: Northern California
Wow, Mike... I gotta get me some'a what you been smokin if you can see that!! (IMG:style_emoticons/default/wink.gif)

--DD
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mueller
post Sep 2 2003, 05:56 PM
Post #16


914 Freak!
***************

Group: Members
Posts: 17,150
Joined: 4-January 03
From: Antioch, CA
Member No.: 87
Region Association: None
Dave,

how can you not invision that?

A new rear housing with gears to change the direction to transmit the power forward (similar to the latest generation of AWD mid-engine Lambos)

Maybe my problem is that I have never smoked anything stronger than a Kool cigerette (IMG:style_emoticons/default/smile.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Dave_Darling
post Sep 3 2003, 11:52 AM
Post #17


914 Idiot
***************

Group: Members
Posts: 15,062
Joined: 9-January 03
From: Silicon Valley / Kailua-Kona
Member No.: 121
Region Association: Northern California
Yeah, straight through the middle of the crankcase! Who needs a camshaft anyway? (IMG:style_emoticons/default/wink.gif)

--DD
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
redshift
post Sep 3 2003, 05:01 PM
Post #18


Bless the Hell out of you!
**********

Group: Members
Posts: 10,926
Joined: 29-June 03
Member No.: 869
Transverse mounting of a /6, with ahh.... two 901s... and a uhhmm... belts... lots of belts... and a chain also.. to tow the car with..

(IMG:style_emoticons/default/smile.gif)


M

-if you can mount a /12 sideways where I saw it, a /6 must fit in a 914..-
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

Reply to this topicStart new topic
4 User(s) are reading this topic (4 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Standard · Switch to: Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 28th November 2024 - 02:50 PM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...