Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

> Fuel Pump wont run off relay board...
D1A3
post Jul 17 2010, 06:30 PM
Post #1


Gruppe Neun Vierzehn Südosten
**

Group: Members
Posts: 362
Joined: 3-June 04
From: Atlanta, GA
Member No.: 2,152
Region Association: South East States
Car died a few weeks ago while driving it and I think I know what is causing it...

Turns out, my fuel pump was not getting power. I temporarily rigged up the pump to run off my driving light relay and the car runs great. I traced the harness power wire (black/red stripe) back all the way to the relay board and could not find any break/melting or anything suspect.

I found in the Haynes Manual that the fuel pump relay should have voltage at 86 and ground at 85. Guess what? I checked and have voltage at 86, but NO ground at 85. The manual says in this case to check the "main relay." What the heck is that? It references the "fuel pump relay" in other places uniquely, so wondering what a "main relay" is on our cars.

Also, mentions that there could be an open circuit causing the ground to fail. What should I check?

The relay being used is known to be good, so any ideas or am I looking at replacing the relay board?

Thanks everyone!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
 
 Reply to this topicStart new topic
Replies(1 - 10)
904svo
post Jul 17 2010, 06:36 PM
Post #2


904SVO
***

Group: Members
Posts: 1,124
Joined: 17-November 05
From: Woodstock,Georgia
Member No.: 5,146
Jason, that ground on pin85 comes from the ecu harness pin#1. Check your grounds at the back of the engine case on the xmas tree grounding point.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
D1A3
post Jul 17 2010, 07:53 PM
Post #3


Gruppe Neun Vierzehn Südosten
**

Group: Members
Posts: 362
Joined: 3-June 04
From: Atlanta, GA
Member No.: 2,152
Region Association: South East States
Thanks Larry. Going to check that now.

BTW: I'll be at the Concours tomorrow at Hennessy. If you are around, stop by!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
D1A3
post Jul 17 2010, 09:26 PM
Post #4


Gruppe Neun Vierzehn Südosten
**

Group: Members
Posts: 362
Joined: 3-June 04
From: Atlanta, GA
Member No.: 2,152
Region Association: South East States
Larry,

Checked the grounds that are just on the passenger side of the air intake and they all are grounded well. Is there another spot Pin85 could get it's ground from? I'm really at a loss here...
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Cap'n Krusty
post Jul 17 2010, 10:53 PM
Post #5


Cap'n Krusty
**********

Group: Members
Posts: 10,794
Joined: 24-June 04
From: Santa Maria, CA
Member No.: 2,246
Region Association: Central California
Two words of advice: "wiring diagram". Available on the Pelican website. The computer supplies the ground. The main power relay is the one forward of the fuel pump relay. From the back: heater fan, fuel pump, main power for the FI system, heated rear window.

The Cap'n
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
swl
post Jul 18 2010, 07:21 AM
Post #6


Senior Member
***

Group: Members
Posts: 1,409
Joined: 7-August 05
From: Kingston,On,Canada
Member No.: 4,550
Region Association: Canada
disconnect the 4 pin connector and jump Pin III to ground. (you are doing what the ECU normally does) Key on. Does the pump run?

If yes then you may want to disconnect the harness from the ECU and inspect the condition of the contacts. Clean as necessary. Reseat the connector and try in normal mode (4 pin connect plugged back in). Remember that the pump will only run for a second or two at key on. Then it shuts down until you start cranking.

If no do you have power at pin 30 of the fuel pump relay?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
SLITS
post Jul 18 2010, 08:18 AM
Post #7


"This Utah shit is HARSH!"
**********

Group: Benefactors
Posts: 13,602
Joined: 22-February 04
From: SoCal Mountains ...
Member No.: 1,696
Region Association: None
Check the main gorund bundle, near relay board on inner fender. Single stud with multiple ground wires. Fuel pump ground wire is one of the bundle.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
ahdoman
post Jul 18 2010, 04:25 PM
Post #8


It's phonetic...Ah-D-O-Man (Audioman)
***

Group: Members
Posts: 667
Joined: 7-November 05
From: Santa Clarita, Ca.
Member No.: 5,084
Region Association: Southern California
Also, don't forget the two fuses on the board next to the relays. One of those is for the fuel pump. They get corroded so wiggle them and make sure the contacts are clean.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
blitZ
post Jul 19 2010, 07:41 AM
Post #9


Beer please...
****

Group: Members
Posts: 2,223
Joined: 31-August 05
From: Lawrenceville, GA
Member No.: 4,719
Region Association: South East States
Did you try swapping out the fuel pump relay on the relay board?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
D1A3
post Feb 20 2011, 05:44 PM
Post #10


Gruppe Neun Vierzehn Südosten
**

Group: Members
Posts: 362
Joined: 3-June 04
From: Atlanta, GA
Member No.: 2,152
Region Association: South East States
OK, Just FINALLY completed a permanent fix for the Fuel pump issue!

To get me by, I had wired the fuel pump into my fog light switch. Worked fine, ran some good auto-crosses and perhaps had a great anti-theft/emergency fuel cutoff...

Tonight I am happy to report that the issue has been resolved. :-) After checking everything that was suggested and running some of my own tests to verify the continuity of the power wire to the fuel pump, I replaced the relay board. Special thanks goes to Al Meredith for his help to locate one for me. (IMG:style_emoticons/default/beerchug.gif)

I know everyone says the relay boards don't go bad, and the one coming out actually looked pretty good (visually speaking). But, good looks don't mean all is well underneath...

Thanks again for everyone's support and you will see me around Atlanta a lot more now that I don't have this to worry about any longer. (IMG:style_emoticons/default/driving.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
markb
post Feb 20 2011, 06:11 PM
Post #11


914less :(
*****

Group: Members
Posts: 5,449
Joined: 22-January 03
From: Nipomo, CA
Member No.: 180
Region Association: Central California
Glad you figured it out. I had a relay board that worked fine most of the time, but on really hot summer days would quit when it got too hot. Replaced it & never had another problem. Of course any car of mine has "unusual" problems. (IMG:style_emoticons/default/biggrin.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Switch to: Standard · Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 27th December 2024 - 02:51 AM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...