 beetle CV flange weirdness |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| mskala |
 Feb 21 2011, 02:45 PM
Post
#1
|
|
R  Group: Members Posts: 1,927 Joined: 2-January 03 From: Massachusetts Member No.: 79 Region Association: None 
 |
A while back I bought the modified type 1 CV's. Just getting to think
about installing. Look at the pic where the outside is machined down. (This is not the modification for 914, this picture is from online of normal type1 CV.)  I can't really show it with a picture, but the flange is built to the larger diameter, so it doesn't match with the machined area. This seems stupid. I guess when bolted down it should still retain the grease, but why is it like this? |
   |
 
|
  |
Replies(1 - 10)
| Cap'n Krusty |
Feb 21 2011, 03:06 PM
Post
#2
|
|
Cap'n Krusty Group: Members Posts: 10,794 Joined: 24-June 04 From: Santa Maria, CA Member No.: 2,246 Region Association: Central California |
The boot goes on the other end of the joint. The cut down portion goes against the flange of the stub axle. The Cap'n
|
|
|
|
| mskala |
Feb 21 2011, 03:22 PM
Post
#3
|
|
R Group: Members Posts: 1,927 Joined: 2-January 03 From: Massachusetts Member No.: 79 Region Association: None
|
But the other side has the recess for the gasket.
QUOTE(Cap'n Krusty @ Feb 21 2011, 04:06 PM)  The boot goes on the other end of the joint. The cut down portion goes against the flange of the stub axle. The Cap'n |
|
|
|
| Cap'n Krusty |
Feb 21 2011, 03:30 PM
Post
#4
|
|
Cap'n Krusty Group: Members Posts: 10,794 Joined: 24-June 04 From: Santa Maria, CA Member No.: 2,246 Region Association: Central California |
Modded CV parts are outside my field of expertise, and I apologize for the apparently erroneous answer. Where's you get the parts?
The Cap'n |
|
|
|
| McMark |
Feb 21 2011, 03:55 PM
Post
#5
|
|
914 Freak! Group: Retired Admin Posts: 20,179 Joined: 13-March 03 From: Grand Rapids, MI Member No.: 419 Region Association: None |
The modified version is installed 'backwards' from the Bug orientation. If you're worried about the boots leaking, you can try some sort of sealant. They've all worked fine for me.
|
|
|
|
| r_towle |
Feb 21 2011, 04:34 PM
Post
#6
|
|
Custom Member Group: Members Posts: 24,662 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States
|
put the gasket on the boot side and sealant on the stub axle side.
The modification is so the CV will fit snug in the stub axle...not the boot. Also, pick up some paint gun cleaning brushes....small wire brushes...and super clean the threads with the brushes, cloths, brakclean...get them all metal, then use locktite on the threads. Rich |
 |
|
| mskala |
Feb 21 2011, 08:03 PM
Post
#7
|
|
R Group: Members Posts: 1,927 Joined: 2-January 03 From: Massachusetts Member No.: 79 Region Association: None
|
Thanks all, I'm pretty sure these are the pmbperformance.com
ones. I'm going with the McMark way for installation, in fact I don't think it's even possible to do otherwise. Not only would the gasket have huge overhang on the thin side, also the pin holes are only drilled out on the thick side. |
|
|
|
| McMark |
Feb 21 2011, 09:23 PM
Post
#8
|
|
914 Freak! Group: Retired Admin Posts: 20,179 Joined: 13-March 03 From: Grand Rapids, MI Member No.: 419 Region Association: None |
QUOTE(r_towle @ Feb 21 2011, 02:34 PM) l, then use locktite on the threads. Rich ACK! No thanks. (IMG:style_emoticons/default/tongue.gif) |
|
|
|
| mskala |
Feb 22 2011, 04:05 PM
Post
#9
|
|
R Group: Members Posts: 1,927 Joined: 2-January 03 From: Massachusetts Member No.: 79 Region Association: None
|
I have never had one loosen as long as a new Schnorr washer was used
and most of the grease kept out of the holes. QUOTE(McMark @ Feb 21 2011, 10:23 PM) QUOTE(r_towle @ Feb 21 2011, 02:34 PM) l, then use locktite on the threads. Rich ACK! No thanks. (IMG:style_emoticons/default/tongue.gif) |
|
|
|
| mskala |
Feb 22 2011, 04:09 PM
Post
#10
|
|
R Group: Members Posts: 1,927 Joined: 2-January 03 From: Massachusetts Member No.: 79 Region Association: None
|
Another similar thread made me look at the pic Chris has at
Tangerine Racing, where he also sells the modified Type I's.  He adds an o-ring so the flange is tight at the sides. |
|
|
|
| ChrisFoley |
Feb 22 2011, 06:43 PM
Post
#11
|
|
I am Tangerine Racing Group: Members Posts: 7,968 Joined: 29-January 03 From: Bolton, CT Member No.: 209 Region Association: None
|
|
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 27th December 2024 - 09:15 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.