Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

> Front wheelwell wheelhouse repair
shuie
post Mar 12 2013, 11:51 AM
Post #1


Member
**

Group: Members
Posts: 352
Joined: 17-May 04
From: baton rouge, la
Member No.: 2,075
Does anyone have any good pictures or experience in repairing the front inner wheelhouse structure of a 914 tub. The best pictures I can find so far are in the bringing out the dead thread. Some really good stuff there with the factory jigs, etc.

At some point my 914 was hit hard enough on the front driver side corner to crumple the front half of the wheel well. Everything in this area was hammered back into place and painted over. I've restored all of the front suspension pieces. I don't know if they are original to the car, but the a-arms & crossmember are straight and bolt onto the car fine, so I think there is a possibility that everything might still be pretty square. I don't have a Tram gauge so I haven't measured the suspension pickup diagonals yet.

Assuming the car is still square enough to fix, I really want to do a proper structural repair. Either with a new fender, wheelhouse, front latch panel, and floorpan, or by building some kind of tube subframe that ties the strut towers and all of the front suspension points together.

Does anyone here have the fixtures to do these repairs?

These pictures are all from Jeff Hail's Bringing out the dead thread.


(IMG:http://www.914world.com/bbs2/uploads_offsite/lh3.googleusercontent.com-2075-1363110702.3.jpg)

(IMG:http://www.914world.com/bbs2/uploads_offsite/lh4.googleusercontent.com-2075-1363110702.4.jpg)

(IMG:http://www.914world.com/bbs2/uploads_offsite/lh6.googleusercontent.com-2075-1363110702.5.jpg)

(IMG:http://www.914world.com/bbs2/uploads_offsite/lh4.googleusercontent.com-2075-1363110702.6.jpg)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
 
 Reply to this topicStart new topic
Replies(1 - 14)
falconfp2001
post Mar 13 2013, 02:43 PM
Post #2


Pancho Pantera
**

Group: Members
Posts: 451
Joined: 5-December 10
From: Downey, CA
Member No.: 12,456
Region Association: Southwest Region
Awesome pics
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
jmill
post Mar 13 2013, 08:41 PM
Post #3


Green Hornet
****

Group: Members
Posts: 2,449
Joined: 9-May 08
From: Racine, Wisconsin
Member No.: 9,038
Region Association: Upper MidWest
You can make one yourself like I did. Check out the link in my signature.


Attached image(s)
Attached Image Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
shuie
post Mar 14 2013, 06:48 AM
Post #4


Member
**

Group: Members
Posts: 352
Joined: 17-May 04
From: baton rouge, la
Member No.: 2,075
jmil, that thread in your signature has a lot of the info I was looking for. Thanks. Nice work!

Yep, if I decide to try to do this myself I will make a similar fixture. I need to measure everything and make sure it's 100% straight and square. I don't know if I know enough to get everything perfectly level and measure everything properly. Im almost ready to put the car on a trailer and send it to someone like Scotty or Series9. If I could get a fixture that I knew was true and confirm that it bolted onto my car I would feel a lot more confident trying the repair myself.

Here is another pic from Jeff Hail's Bringing out the dead thread that shows the measurements I am going to look at first. I think I need a Tram gauge to get these right.

(IMG:http://www.914world.com/bbs2/uploads_offsite/lh4.googleusercontent.com-2075-1363268003.1.jpg)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
shuie
post Mar 15 2013, 06:30 AM
Post #5


Member
**

Group: Members
Posts: 352
Joined: 17-May 04
From: baton rouge, la
Member No.: 2,075
Does anyone know if the wheelhouse panels were different on an early car vs. a later impact bumper car? Repair panels for this part of the car are not real easy to find.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
gms
post Mar 15 2013, 09:44 AM
Post #6


Advanced Member
****

Group: Members
Posts: 2,708
Joined: 12-March 04
From: Chicagoland
Member No.: 1,785
Region Association: Upper MidWest
QUOTE(shuie @ Mar 15 2013, 07:30 AM) *

Does anyone know if the wheelhouse panels were different on an early car vs. a later impact bumper car? Repair panels for this part of the car are not real easy to find.

The front wheel houses are the same all years except for the very early cars (1969) with different cowl and front fenders.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
A&PGirl
post Mar 15 2013, 01:00 PM
Post #7


Senior Member
***

Group: Members
Posts: 1,019
Joined: 4-January 06
From: Oklahoma
Member No.: 5,367
Region Association: None
I'm very interested in this as well. I have to replace both wheelwell and wheelhouses on my OSU orange car.

User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Katmanken
post Mar 15 2013, 05:51 PM
Post #8


You haven't seen me if anybody asks...
****

Group: Members
Posts: 4,738
Joined: 14-June 03
From: USA
Member No.: 819
Region Association: Upper MidWest
Me too.

I've got a car where the DAPO bondo'd the left wheelhouse, and the bulkhead had a deflection in the middle.

Paging Rick Ollah.....
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
gms
post Mar 16 2013, 10:40 AM
Post #9


Advanced Member
****

Group: Members
Posts: 2,708
Joined: 12-March 04
From: Chicagoland
Member No.: 1,785
Region Association: Upper MidWest
QUOTE(Katmanken @ Mar 15 2013, 06:51 PM) *

Me too.

I've got a car where the DAPO bondo'd the left wheelhouse, and the bulkhead had a deflection in the middle.

Paging Rick Ollah.....

If you are close to Portage IN contact Garold Shaffer as he parts out a lot of cars and would have the sheet metal you need.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
gms
post Mar 16 2013, 10:42 AM
Post #10


Advanced Member
****

Group: Members
Posts: 2,708
Joined: 12-March 04
From: Chicagoland
Member No.: 1,785
Region Association: Upper MidWest
QUOTE(Katmanken @ Mar 15 2013, 06:51 PM) *

Me too.

I've got a car where the DAPO bondo'd the left wheelhouse, and the bulkhead had a deflection in the middle.

Paging Rick Ollah.....

If you are close to Portage IN contact Garold Shaffer as he parts out a lot of cars and would have the sheet metal you need.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
shuie
post Mar 23 2013, 11:45 AM
Post #11


Member
**

Group: Members
Posts: 352
Joined: 17-May 04
From: baton rouge, la
Member No.: 2,075
Any tricks for getting an accurate measurement of the suspension points without a tram gauge while the tub is on jack stands? I really don't want to buy a tool like that for a one time use.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
FourBlades
post Mar 23 2013, 11:49 AM
Post #12


From Wreck to Rockin
****

Group: Members
Posts: 2,056
Joined: 3-December 07
From: Brevard, FL
Member No.: 8,414
Region Association: South East States
Buy long bolts to put into the holes and stretch a tape measure between them.

I think my tram gauge from auto body tool house was around $250 or so.

They are useful for doing alignment checks as well.

John
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
shuie
post Mar 23 2013, 12:22 PM
Post #13


Member
**

Group: Members
Posts: 352
Joined: 17-May 04
From: baton rouge, la
Member No.: 2,075
QUOTE(FourBlades @ Mar 23 2013, 12:49 PM) *

Buy long bolts to put into the holes and stretch a tape measure between them.



yep, tried that first. The longest bolts I could find from the hardware store don't clear the bottom of the tub from the rear suspension console. I'll try a bolt store next week to see if they have something longer.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
mr914
post Mar 23 2013, 05:03 PM
Post #14


914 Hillbilly
***

Group: Members
Posts: 576
Joined: 11-January 03
From: Lincoln NE
Member No.: 131
Region Association: None
QUOTE(gms @ Mar 15 2013, 11:44 AM) *

QUOTE(shuie @ Mar 15 2013, 07:30 AM) *

Does anyone know if the wheelhouse panels were different on an early car vs. a later impact bumper car? Repair panels for this part of the car are not real easy to find.

The front wheel houses are the same all years except for the very early cars (1969) with different cowl and front fenders.



I thought I was seeing things while putting my early 6 together (IMG:style_emoticons/default/w00t.gif) . Know it makes sense
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
sixnotfour
post Mar 23 2013, 05:40 PM
Post #15


914 Wizard
**********

Group: Members
Posts: 10,681
Joined: 12-September 04
From: Life Elevated..planet UT.
Member No.: 2,744
Region Association: Rocky Mountains
buy some all thread and cut to length
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

Reply to this topicStart new topic
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Switch to: Standard · Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 27th December 2024 - 03:11 AM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...