 Dellortos, PSI ? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| 80cap |
 Aug 3 2016, 10:41 AM
Post
#1
|
|
Member  Group: Members Posts: 320 Joined: 6-February 15 From: ohio Member No.: 18,405 Region Association: None  |
What PSI is ideal for a pair of 40's on a 2056 engine?
Brian |
   |
 
|
  |
Replies(1 - 6)
| billh1963 |
Aug 3 2016, 11:56 AM
Post
#2
|
|
Car Hoarder! Group: Members Posts: 3,405 Joined: 28-March 11 From: North Carolina Member No.: 12,871 Region Association: South East States |
I've read 3 psi is optimal
|
|
|
|
| GregAmy |
Aug 3 2016, 12:18 PM
Post
#3
|
|
Advanced Member Group: Members Posts: 2,411 Joined: 22-February 13 From: Middletown CT Member No.: 15,565 Region Association: North East States 
|
^^^
Pressure needs to be enough to flow fuel to keep the bowl full, without over-powering the floats. 3psi would be just fine. |
|
|
|
| porschetub |
Aug 3 2016, 01:54 PM
Post
#4
|
|
Advanced Member Group: Members Posts: 4,754 Joined: 25-July 15 From: New Zealand Member No.: 18,995 Region Association: None |
I did some testing on my 1.8 with Weber rebuilt DCNF's a few years ago with Moprod low pressure pump mounted under the tank,holley low pressure regulator and gauge at engine.
I found this type of regulator won't go much lower than 3 psi,I noted a drop in pressure at revs I guessed this was the distance from pump to tank. Set pressure at 3.2 psi and at stayed constant @ 3+,increased pressure to 3.4 and it went rich on idle,increased it to 3.5 and it flooded,coughed and stalled. Some may have different experience but my test proved the needle and seats started to be overcome by pressure @ 3.4 psi,I'am sure this would apply to Dellorto's also. I feel that's important to choose a pump that doesn't make too much more pressure that you need,my pump makes 6psi which is a good matchup for the holley low pressure regulator. |
 |
|
| GregAmy |
Aug 3 2016, 02:42 PM
Post
#5
|
|
Advanced Member Group: Members Posts: 2,411 Joined: 22-February 13 From: Middletown CT Member No.: 15,565 Region Association: North East States
|
QUOTE(porschetub @ Aug 3 2016, 03:54 PM)  Some may have different experience but my test proved the needle and seats started to be overcome by pressure @ 3.4 psi,I'am sure this would apply to Dellorto's also. Interesting. I may dial mine down a tad from 3 (Dellortos). I don't see any problems with <3 and the pressure reducing at WOT, as long as the engine isn't going lean (indicating the pump isn't keeping up with the flow through the carbs). After all, how much gph are we flowing with these engines? Probably not much. And, of course, unlike fuel injection the delivery pressure is not relevant to the running of the engine as long as the pump can keep the bowls filled and not over-power the float. For reference I'm running a GM in-tank pump within a Fuelsafe cell, using a Holley 12-804 regulator. |
|
|
|
| anderssj |
Aug 3 2016, 04:11 PM
Post
#6
|
|
Dog is my copilot... Group: Members Posts: 1,715 Joined: 28-January 03 From: VA Member No.: 207 Region Association: MidAtlantic Region
|
Running mine at 3 . . . for years now.
|
|
|
|
| Jake Raby |
Aug 4 2016, 12:45 AM
Post
#7
|
|
Engine Surgeon Group: Members Posts: 9,398 Joined: 31-August 03 From: Lost Member No.: 1,095 Region Association: South East States |
2.5 is optimum, 3 is on the upper end and a weak needle valve will not hold it. I shoot for 2 PSI dynamic and its typically very safe.
|
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 26th December 2024 - 03:02 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.