 Fuel Pressure Regulator |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| StratPlayer |
 Nov 13 2024, 08:20 PM
Post
#1
|
|
StratPlayer  Group: Members Posts: 3,298 Joined: 27-December 02 From: SLC, Utah Member No.: 27 Region Association: Rocky Mountains 
 |
Going to slap one of these into my new motor, I saw where PMB was building a new 2258 and had one of these units installed on the motor.
https://thedubshop.com/universal-fuel-press...or-package-914/ |
   |
 
|
  |
Replies(1 - 8)
| bkrantz |
Nov 13 2024, 08:29 PM
Post
#2
|
|
914 Guru Group: Members Posts: 8,154 Joined: 3-August 19 From: SW Colorado Member No.: 23,343 Region Association: Rocky Mountains
|
That's what I have in my system (from the Dub Shop). No complaints, so it must be working. (IMG:style_emoticons/default/biggrin.gif)
Actually, I do know that it reaches and holds required pressure, based on when I had a manual gauge plumbed into the engine fuel line loop. |
|
|
|
| GregAmy |
Nov 13 2024, 08:31 PM
Post
#3
|
|
Advanced Member Group: Members Posts: 2,399 Joined: 22-February 13 From: Middletown CT Member No.: 15,565 Region Association: North East States
|
I use it on my Microsquirt-converted D-Jet. 3-bar solid with my standard D-Jet pump.
Also used it on my Microsquirt-converted Toyota MR2 race car. Solid there, too. |
|
|
|
| jim_hoyland |
Nov 15 2024, 12:34 PM
Post
#4
|
|
Get that VIN ? Group: Members Posts: 9,527 Joined: 1-May 03 From: Sunset Beach, CA Member No.: 643 Region Association: Southern California
|
QUOTE(StratPlayer @ Nov 13 2024, 06:20 PM)  Going to slap one of these into my new motor, I saw where PMB was building a new 2258 and had one of these units installed on the motor. https://thedubshop.com/universal-fuel-press...or-package-914/ How did you mount it ? I’m |
|
|
|
| StratPlayer |
Nov 15 2024, 04:22 PM
Post
#5
|
|
StratPlayer Group: Members Posts: 3,298 Joined: 27-December 02 From: SLC, Utah Member No.: 27 Region Association: Rocky Mountains
|
QUOTE(jim_hoyland @ Nov 15 2024, 11:34 AM) QUOTE(StratPlayer @ Nov 13 2024, 06:20 PM) Going to slap one of these into my new motor, I saw where PMB was building a new 2258 and had one of these units installed on the motor. https://thedubshop.com/universal-fuel-press...or-package-914/ How did you mount it ? I’m It mounts where the old fuel pressure regulator goes install is easy. |
|
|
|
| jim_hoyland |
Nov 15 2024, 07:21 PM
Post
#6
|
|
Get that VIN ? Group: Members Posts: 9,527 Joined: 1-May 03 From: Sunset Beach, CA Member No.: 643 Region Association: Southern California
|
Can it adjust the fuels pressure ?
|
|
|
|
| bkrantz |
Nov 15 2024, 08:17 PM
Post
#7
|
|
914 Guru Group: Members Posts: 8,154 Joined: 3-August 19 From: SW Colorado Member No.: 23,343 Region Association: Rocky Mountains
|
Here's how I mounted mine. First the Dub Shop bracket.
Attached thumbnail(s) 
|
|
|
|
| bkrantz |
Nov 15 2024, 08:19 PM
Post
#8
|
|
914 Guru Group: Members Posts: 8,154 Joined: 3-August 19 From: SW Colorado Member No.: 23,343 Region Association: Rocky Mountains
|
And regulator.
Attached thumbnail(s) 
|
|
|
|
| GregAmy |
Nov 16 2024, 08:08 AM
Post
#9
|
|
Advanced Member Group: Members Posts: 2,399 Joined: 22-February 13 From: Middletown CT Member No.: 15,565 Region Association: North East States
|
QUOTE(StratPlayer @ Nov 15 2024, 05:22 PM) QUOTE(jim_hoyland @ Nov 15 2024, 11:34 AM) How did you mount it ? It mounts where the old fuel pressure regulator goes install is easy. Ditto. I just screwed mine into that same flange using its fittings. QUOTE(jim_hoyland @ Nov 15 2024, 08:21 PM) Can it adjust the fuels pressure ? No, it's fixed at 3 bar. If you're tuning most EFIs at our level then that's a good baseline. Stock D-Jet fuel pressure is 28; 3 bar is 43.5 psi. You could account for that with a tunable MPS from Tangerine: https://tangerineracing.com/shop/ols/produc...t-mps-diaphragm Mario also offers a 4 bar: https://thedubshop.com/fuel-pressure-regulator-builder/ Being a standard Bosch regulator, you could possibly find alternatives. |
|
|
|
|
5 User(s) are reading this topic (5 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 28th November 2024 - 02:44 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.