Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

> DIY Alignment
germaneighter
post Jun 7 2006, 09:52 AM
Post #1


Member
**

Group: Members
Posts: 130
Joined: 9-August 05
From: Tulsa, OK
Member No.: 4,563
Does anyone have detailed instructions for doing an "at home" driveway alignment? (with pictures would be nice)

Rear Shims are no problem. I can get some laser cut in different thicknesses.


(Local independent Porsche shop estimates $400 for a proper alignment.)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
 
 Reply to this topicStart new topic
Replies(1 - 17)
Rand
post Jun 7 2006, 10:34 AM
Post #2


Cross Member
*****

Group: Members
Posts: 7,409
Joined: 8-February 05
From: OR
Member No.: 3,573
Region Association: None
Some info...
link1
link2


I would think a well written how-to with photos would make an automatic classic thread.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Joe Ricard
post Jun 7 2006, 10:46 AM
Post #3


CUMONIWANNARACEU
*****

Group: Members
Posts: 6,811
Joined: 5-January 03
From: Gautier, MS
Member No.: 92
Crap I just did one on my car Monday evening.

From rear shims to Front camber caster
front and rear toe.

I get gun shy posting pics of my Red Neck procedures as it is surely not up to the standards some here are accustomed to.

But the results are hardly questionable. goes straight turns in quickly and heats the tires evenly across the face.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
John Se
post Jun 7 2006, 11:03 AM
Post #4


Newbie
*

Group: Members
Posts: 29
Joined: 14-February 06
From: Scottsdale AZ
Member No.: 5,579
You need the book "prepare to win" by caroll smith

just need some strings or long bars to create a parrallelogram (sic?) arount the car and measure it up
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
germaneighter
post Jun 7 2006, 01:16 PM
Post #5


Member
**

Group: Members
Posts: 130
Joined: 9-August 05
From: Tulsa, OK
Member No.: 4,563
QUOTE(Rand @ Jun 7 2006, 08:34 AM) *

Some info...
link1
link2


I would think a well written how-to with photos would make an automatic classic thread.




Great...thanks very much.

dave
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
john rogers
post Jun 7 2006, 01:44 PM
Post #6


Senior Member
***

Group: Members
Posts: 1,525
Joined: 4-March 03
From: Chula Vista CA
Member No.: 391
I have an article on the Pelican site and it has conversions for fractions of an inch to degrees camber and toe in/out for 15 inch wheels included.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Joe Ricard
post Jun 7 2006, 02:10 PM
Post #7


CUMONIWANNARACEU
*****

Group: Members
Posts: 6,811
Joined: 5-January 03
From: Gautier, MS
Member No.: 92
Yup John's article rocks!!!!
http://www.pelicanparts.com/techarticles/h...home_toe_in.htm
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Rand
post Jun 7 2006, 02:16 PM
Post #8


Cross Member
*****

Group: Members
Posts: 7,409
Joined: 8-February 05
From: OR
Member No.: 3,573
Region Association: None
Link? Guess I can go search later, but if you have it that would be nice.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
KenH
post Jun 7 2006, 04:57 PM
Post #9


Senior Member
***

Group: Members
Posts: 680
Joined: 16-January 03
From: Gilroy, CA
Member No.: 156
Read these. You can make "strings" with conduit and attach to the car by the license plate screws. You can buy a caster/camber tool off ebay. You wil spend a lot less and have a set-up you can use again. Email me if you want more info.

Ken

http://www.smartracingproducts.com/pdfdocs...mber_manual.pdf

http://www.smartracingproducts.com/pdfdocs...ings_manual.pdf

Oh - turnplates can be 2 sections of slippery masonite placed "face-to-face"
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
germaneighter
post Jun 8 2006, 12:57 PM
Post #10


Member
**

Group: Members
Posts: 130
Joined: 9-August 05
From: Tulsa, OK
Member No.: 4,563
Is toe measured from the wheel or the tire?

It seems 1/8" total toe in at the front of the tire would be slightly less at the front of the rim.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Joe Ricard
post Jun 8 2006, 01:09 PM
Post #11


CUMONIWANNARACEU
*****

Group: Members
Posts: 6,811
Joined: 5-January 03
From: Gautier, MS
Member No.: 92
RIM
Because John's figures are off of a 15" circle.
I would try 1/16" toe in on each wheel for a total of 1/8" toe in.

I did 1/32 toe out the other day and it's not quite enough as the car kinda wanders. More toe out will give me quicker turn in low speed cone dodging.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
KenH
post Jun 8 2006, 01:09 PM
Post #12


Senior Member
***

Group: Members
Posts: 680
Joined: 16-January 03
From: Gilroy, CA
Member No.: 156
Porsche specifies Toe in "degrees". Measure from the rim. You will have to calculate degrees as it depends on the "measured" diameter of the rim.

Ken
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Joe Ricard
post Jun 8 2006, 01:23 PM
Post #13


CUMONIWANNARACEU
*****

Group: Members
Posts: 6,811
Joined: 5-January 03
From: Gautier, MS
Member No.: 92
Yup degrees is good BUT John makes it easier
Toe measurement 1/16 inch or 0.0625 inch = Toe angle 8.95251minutes
Toe measurement 1/8 inch or 0.125 inch = Toe angle 17.9051 minutes
Toe measurement 3/16 inch or 0.1875 inch = Toe angle 26.8578 minutes
Toe measurement ¼ inch or 0.25 inch = Toe angle 35.8106 minutes
Toe measurement 5/16 inch or 0.3125 inch = Toe angle 44.7638 minutes
Toe measurement 3/8 inch or 0.375 inch = Toe angle 53.7172 minutes
Toe measurement 7/16 inch or 0.4375 inch = Toe angle 1.04452 degrees
Toe measurement ½ inch or 0.5 inch = Toe angle 1.19375 degrees
Toe measurement 9/16 inch or 0.5625 inch = Toe angle 1.343 degrees
Toe measurement 5/8 inch or 0.625 inch = Toe angle 1.49225 degrees
Toe measurement 11/16 inch or 0.6875 inch = Toe angle 1.64152 degrees
Toe measurement ¾ inch or 0.75 inch = Toe angle 1.79079 degrees
Toe measurement 13/16 inch or 0.8125 inch = Toe angle 1.94008 degrees
Toe measurement 7/8 inch or 0.875 inch = Toe angle 2.08938 degrees
Toe measurement 15/16 inch or 0.9375 inch = Toe angle 2.23869 degrees
Toe measurement 1 inch = Toe angle 2.38802 degrees
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
germaneighter
post Jun 9 2006, 03:55 PM
Post #14


Member
**

Group: Members
Posts: 130
Joined: 9-August 05
From: Tulsa, OK
Member No.: 4,563
Can use a magnetic angle finder mounted directly to the strut body to set caster?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
germaneighter
post Jun 9 2006, 10:34 PM
Post #15


Member
**

Group: Members
Posts: 130
Joined: 9-August 05
From: Tulsa, OK
Member No.: 4,563
I meant that as a question....Can I use a magnetic angle finder mounted directly to the strut body to set caster?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
nbscooters
post Jun 10 2006, 12:45 AM
Post #16


Member
**

Group: Members
Posts: 165
Joined: 29-June 05
Member No.: 4,347
Region Association: None
if you use the string method, you would need at least 3 people when you adjust the front; one to hold the steering wheel inside the car, one to adjust the tow underneath the car, and one to tell you the measurements from the wheel to the string.


i align 911's for post races.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mr.C
post Jun 10 2006, 12:58 AM
Post #17


Easy does it
***

Group: Members
Posts: 611
Joined: 31-December 02
From: Central Cal
Member No.: 61
Region Association: None
QUOTE(germaneighter @ Jun 9 2006, 09:34 PM) *

I meant that as a question....Can I use a magnetic angle finder mounted directly to the strut body to set caster?

I was wondering the same exact thing.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
john rogers
post Jun 10 2006, 07:37 AM
Post #18


Senior Member
***

Group: Members
Posts: 1,525
Joined: 4-March 03
From: Chula Vista CA
Member No.: 391
Yes. My rule of thumb is to set the top strut mount as far back as possible for the street, for stability. Set it forward for faster turn in or less camber. If you read the fine print in the article, it is for initial steup or in case of a off at the races and should not be used in place of a professional shop alignment for long term use.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

Reply to this topicStart new topic
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Switch to: Standard · Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 28th November 2024 - 09:41 PM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...