 Pilot bearing in the crank, is this going to be an issue? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| VaccaRabite |
 Mar 15 2008, 03:16 PM
Post
#1
|
|
En Garde!  Group: Admin Posts: 13,584 Joined: 15-December 03 From: Dallastown, PA Member No.: 1,435 Region Association: MidAtlantic Region  |
Isn't this bearing supposed to be in the flywheel?
How do I get the bugger out? What should I do here? (IMG:http://farm4.static.flickr.com/3182/2335190315_28837f1729.jpg) If it is not an issue, please let me know. Its in there pretty good. I figure I am going to have to weld a bolt to it to get it out. Right now, I have no purchase. Zach |
   |
 
|
  |
Replies
| brer |
Mar 28 2008, 12:09 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 2,555 Joined: 10-March 05 From: san diego Member No.: 3,736 Region Association: None |
you could have better luck putting some heat shrink wire wrap on the pipe to fit it.
tape doesn't work as the force of the grease is intense. |
|
|
|
Posts in this topic
Vacca Rabite Pilot bearing in the crank Mar 15 2008, 03:16 PM
brp986s the pilot bearing goes in the flywheel, not the cr... Mar 15 2008, 04:01 PM
SirAndy
the pilot bearing goes in the flywheel, not the c... Mar 15 2008, 04:32 PM McMark Get some bearing grease and pack, pack, pack it in... Mar 15 2008, 04:24 PM Vacca Rabite
Anyone have a good reason not to just leave that ... Mar 15 2008, 04:39 PM brer There is a spacer that goes in the crank and its n... Mar 15 2008, 04:51 PM BIGKAT_83
Get some bearing grease and pack, pack, pack it i... Mar 15 2008, 05:13 PM Mark Henry Dude it comes out real easy. I use a autobody slid... Mar 15 2008, 05:38 PM Krieger914 Put a couple of bolts in the end of the fw and use... Mar 15 2008, 09:12 PM brer +1 for grease and tight fitting rod, or better yet... Mar 15 2008, 09:55 PM LvSteveH For what it's worth I had a car running dual p... Mar 15 2008, 10:45 PM davep The 411, at least, had the bearing in the crank li... Mar 16 2008, 08:30 AM Gint Seems like you could cut the cage with a saw blade... Mar 16 2008, 08:57 AM brer there is also that felt washer that goes in.
with... Mar 16 2008, 09:59 AM davep Well, the bearing in his photo is not properly sea... Mar 16 2008, 06:35 PM Vacca Rabite Well, I treid the grease trick last night to pop t... Mar 28 2008, 11:58 AM jkeyzer this is one of those things where if you take a sh... Mar 28 2008, 12:11 PM Cap'n Krusty All this verbiage, and not much in the way of a re... Mar 28 2008, 12:42 PM davep
It's likely that the T4 with a manual tranny ... Mar 28 2008, 08:35 PM Krieger914 Don't worry about it. If you put another bear... Mar 28 2008, 02:32 PM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 31st October 2024 - 07:28 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.