 Sound from the rear-Part II, Bushing not greaed properly |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| jim_hoyland |
 Sep 8 2008, 08:32 PM
Post
#1
|
|
Get that VIN ?  Group: Members Posts: 9,572 Joined: 1-May 03 From: Sunset Beach, CA Member No.: 643 Region Association: Southern California 
 |
The sound finally went away with an heavier application from the grease gun into the zirks yesterday. I used a heavy duty tractor bearing grease
I have been told that the bushing should have silicone grease on their outer surface and under the flange, which makes sense now. So I'll pull the arms, remove the bushings and try the silicone grease. The creak started to come back today, albeit less noisy. Any tip on do's / dont's on greasing bushings will be appreciated |
   |
 
|
  |
Replies
| Eric_Shea |
Sep 9 2008, 03:24 PM
Post
#2
|
|
PMB Performance Group: Admin Posts: 19,289 Joined: 3-September 03 From: Salt Lake City, UT Member No.: 1,110 Region Association: Rocky Mountains  |
(IMG:style_emoticons/default/jerkit.gif)
QUOTE you agreed with that advice and threw a few insults in for good measure. I pasted what I typed to Jim in a personal email that evening without seeing your "advice." If by insults you mean I "questioned" if you had seen these bushings or, I offered a different opinion than yours... OK. QUOTE your an ass Now you're down to name calling. That's not good. (IMG:style_emoticons/default/wink.gif) Keep it up. |
 |
|
Posts in this topic
jim_hoyland Sound from the rear-Part II Sep 8 2008, 08:32 PM
r_towle My first piece of advice would be to bin them.
Get... Sep 8 2008, 08:49 PM
r_towle
If you must stick with the plastic.
take a dremel... Sep 9 2008, 11:57 AM Eric_Shea Rich, are you familiar with the hardness measureme... Sep 8 2008, 10:51 PM r_towle
Rich, are you familiar with the hardness measurem... Sep 9 2008, 08:11 AM r_towle
Its an opinion, nothing to get personal about.... Sep 9 2008, 11:16 AM Eric_Shea Frankly, I think (know) you're talking out of ... Sep 9 2008, 09:26 AM r_towle
Frankly, I think (know) you're talking out of... Sep 9 2008, 09:49 AM Eric_Shea
Wonder why I would respond the way I do? :idea:... Sep 9 2008, 10:58 AM r_towle sounds like a sales response.
his are squeaking/cr... Sep 9 2008, 11:11 AM mikez Hmmm, on a recent install of hard bushings I got l... Sep 9 2008, 11:41 AM Eric_Shea
I responded with the correct information in my v... Sep 9 2008, 11:46 AM 736conver
No your first response was to throw away the pro... Sep 9 2008, 12:02 PM greenie Guys,
Just a thought ... maybe it's not the b... Sep 9 2008, 12:05 PM jim_hoyland :rotfl: :rotfl: :rotfl: :rotfl: I switched over... Sep 9 2008, 12:10 PM Eric_Shea Grooves are unnecessary. ;)
Zerks are in the ins... Sep 9 2008, 12:15 PM r_towle I would shut up if you offered help and advice ins... Sep 9 2008, 12:30 PM Eric_Shea
Hmmmm... let's see :idea:
I get it! I... Sep 9 2008, 12:53 PM mikez :popcorn: :cheer: :rotfl: Sep 9 2008, 01:33 PM r_towle I will quote myself so you can remember.
you agre... Sep 9 2008, 03:22 PM 736conver Rich you first response was.
You trashed Eric w... Sep 9 2008, 03:33 PM r_towle I did not know that Eric made these bushings.
I kn... Sep 9 2008, 03:36 PM Eric_Shea
Like what Rich? I've simply replied to ever... Sep 9 2008, 03:57 PM r_towle
Ok, so my answer was not straight...grease fittin... Sep 9 2008, 05:09 PM Eric_Shea :jerk:
Take your meds. Sep 9 2008, 06:25 PM Rusty Gentlemen,
We're all friends here... looking ... Sep 9 2008, 07:29 PM mikez http://web01.genmay.com/userav/avatars/sobeavatar.... Sep 9 2008, 08:14 PM rhodyguy ha. what a thread. DING! gentlemen, to your co... Sep 9 2008, 09:16 PM sixnotfour
whatever, I got rollers.
my plastic ones wont e... Sep 9 2008, 09:23 PM rhodyguy rolls it out. calling... Sep 9 2008, 09:29 PM Eric_Shea I've got Rollers on one car and Elephants on t... Sep 9 2008, 10:41 PM |
21 User(s) are reading this topic (21 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 6th January 2025 - 10:18 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.