 the sinister urge, no more DSM... (and slowly getting pictures fixed in old posts) |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| RJMII |
 Nov 3 2008, 02:49 PM
Post
#1
|
|
Jim McIntosh  Group: Members Posts: 3,125 Joined: 11-September 07 From: Sandy, Utah Member No.: 8,112 Region Association: None  |
I'm starting to re-assemble my car.
|
   |
 
|
  |
Replies
| echocanyons |
Nov 3 2008, 10:17 PM
Post
#2
|
|
Advanced Member Group: Benefactors Posts: 2,103 Joined: 24-December 02 From: Bay Area, CA Member No.: 7 Region Association: Central California 
|
Cool Project!
I stopped in Worland several years back and was super suprised to see a 914 in the showroom of.....hmmm.....I forget maybe an electronics or car audio store. If I remember right, the store was on a main street or something. You don't remember thhat do you, or maybe it was your car, there can't be too many 914's in that town. |
|
|
|
Posts in this topic
RJMII the sinister urge Nov 3 2008, 02:49 PM
Root_Werks You'll run into 100+ things you'll need wh... Nov 3 2008, 06:36 PM RJMII What it looked like when I traded my Toyota 4Runne... Nov 3 2008, 07:31 PM RJMII my parts car:
Working over the front suspension... Nov 3 2008, 07:37 PM RJMII Rear wheel on with 1" spacer. going to go wit... Nov 3 2008, 08:15 PM RJMII car in the shop now:
http://inlinethumb46.webshot... Nov 3 2008, 09:39 PM RJMII I just like the way it looks in there:
http://inli... Nov 3 2008, 09:49 PM RJMII 2.5 inch mandrel bent exhaust pieces for intake pl... Nov 3 2008, 09:53 PM RJMII so... right now I'm at the point of going to g... Nov 3 2008, 09:57 PM SGB Um...
Good start! Jeeez-pers. :)
:beer2: Nov 3 2008, 10:09 PM
RJMII
Cool Project!
I stopped in Worland several ... Nov 3 2008, 10:25 PM RJMII I found a picture of the engine mount being fitted... Nov 3 2008, 10:22 PM RJMII and... what I get to the machine shop with while w... Nov 4 2008, 12:33 AM RJMII I was doing some engine work today.
If you notic... Feb 18 2009, 11:39 AM RJMII Here it is with a test fit, to see where that TB e... Feb 18 2009, 11:42 AM RJMII And here it is, with the top half back on and the ... Feb 18 2009, 11:43 AM andys RJMII,
What V6 motor is that?
Andys Feb 18 2009, 12:14 PM RJMII mitsubishi 6G73. 2.5 liter V-6 SOHC 24 valves; and... Feb 18 2009, 08:50 PM RJMII I got the engine back in; here are the results. =o... Feb 18 2009, 09:01 PM RJMII The piece of metal across the top of the firewall;... Feb 18 2009, 09:02 PM Solo914
The piece of metal across the top of the firewall... Feb 18 2009, 09:40 PM RJMII
The piece of metal across the top of the firewal... Feb 18 2009, 10:02 PM rick 918-S
The piece of metal across the top of the firewall... Feb 18 2009, 11:28 PM RJMII Starting to look like a water cooled conversion...... Apr 7 2009, 03:49 PM RJMII I had my favorite machinist cut and weld the intak... Apr 7 2009, 03:53 PM schreiber Helluva build thread. Keep up the good work! Apr 7 2009, 04:06 PM Zardozz That's almost as crazy plumbing as mine. I... Apr 7 2009, 04:44 PM RJMII downpipe from turbo to exhaust... Apr 20 2009, 01:44 PM RJMII The engine is back out of the car, also. Time to ... Apr 21 2009, 09:25 PM RJMII Transmission mounts. stock ones. I was under my ca... Apr 22 2009, 07:38 PM RJMII Transmission mounts... 911 sport units. Twenty min... Apr 22 2009, 07:40 PM RJMII Slowly getting there. =o) The downpipe needs tweak... Apr 22 2009, 07:42 PM RJMII :sawzall:
Back ugly bumper off. anyone want to ... Apr 22 2009, 07:44 PM RJMII :sawzall: ---> that's going to get some ho... Apr 22 2009, 07:46 PM RJMII every 914 owners dream... an empty jackstand. =o)
... Apr 22 2009, 07:48 PM RJMII Starting fitment of the plumbing between the turbo... Apr 30 2009, 01:20 AM RJMII Slowly getting there. The Orange reducer is hiding... Apr 30 2009, 01:21 AM RJMII better angle...
If you look at the orange, the p... Apr 30 2009, 01:23 AM RJMII I scored a set of 360cc injectors. These are stock... Apr 30 2009, 04:04 PM RJMII ...and installed in the fuel rail and lower intake... Apr 30 2009, 04:07 PM RJMII got the angle fixed for the pipe between the turbo... May 1 2009, 08:23 PM JRust Looking good Jim! Keep up the good work May 1 2009, 08:41 PM nsr-jamie Wow ! That is cool !! Now I know what ... May 2 2009, 10:49 PM dlo914 Not going to run an intercooler? May 2 2009, 11:58 PM RJMII Daniel, the plan is to go with a water to air inte... May 3 2009, 11:06 AM RJMII I got the air filter, and the silicone connector f... May 11 2009, 09:27 PM RJMII Here's a hole in the oil pan for the oil retur... May 30 2009, 10:51 PM RJMII Oil return line installed. (It needs reconfigured ... May 30 2009, 10:51 PM RJMII Oil feed line installed. =o) all of the shiny copp... May 30 2009, 10:51 PM RJMII Test fitting the intake tubes with the engine in t... May 30 2009, 10:51 PM RJMII While I was drilling holes for wires, throttle cab... May 30 2009, 10:52 PM 6freak
While I was drilling holes for wires, throttle ca... Jun 1 2009, 08:29 AM RJMII The wires are all sorted, and ready to be routed a... May 30 2009, 10:52 PM RockinOldSchool So did you swap in HIDs after you took the pic? Or... May 30 2009, 11:32 PM RJMII I'm just running the cheap Xenon bulbs for now... May 30 2009, 11:57 PM RockinOldSchool
I'm just running the cheap Xenon bulbs for no... May 31 2009, 12:02 AM RJMII I'd be interested in the hi/low kit... I'm... May 31 2009, 08:40 PM RockinOldSchool
I'd be interested in the hi/low kit... I... Jun 1 2009, 01:05 AM 3d914 Jim,
This is a radical 914. Very cool! What a... May 31 2009, 11:28 PM RJMII Gerard, thank you! We are aiming for 300-350hp... Jun 1 2009, 11:02 AM 6freak
Gerard, thank you! We are aiming for 300-350h... Jun 1 2009, 11:20 AM RockinOldSchool
Gerard, thank you! We are aiming for 300-350h... Jun 1 2009, 11:35 AM RJMII John,
I've got the turn signal switch I pul... Jun 1 2009, 12:24 PM RockinOldSchool
I've got the turn signal switch I pulled sti... Jun 1 2009, 01:20 PM RJMII Ah, with that Evo engine you are going to end up w... Jun 1 2009, 11:39 PM RJMII progress picture number one from today.
spaghetti... Jun 2 2009, 01:49 AM RJMII Progress pic number two today!
all taped up ... Jun 2 2009, 01:51 AM mojorisen914 It's about damn time you got out there and did... Jun 2 2009, 02:47 AM RJMII
It's about damn time you got out there and di... Jun 2 2009, 02:52 AM RJMII test fitting the exhaust. hmm...
straight out, o... Jun 4 2009, 03:22 PM 6freak
test fitting the exhaust. hmm...
straight out, ... Jun 4 2009, 03:44 PM RJMII I'm test fitting the radiator...
trying to g... Jun 4 2009, 03:39 PM JRust "I'm test fitting the radiator...
trying ... Jun 4 2009, 05:00 PM RJMII 6freak/Mike...
here is another angle. The exhaus... Jun 4 2009, 06:41 PM 6freak
6freak/Mike...
here is another angle. The exhau... Jun 5 2009, 08:57 AM RJMII Time to go put this on... Jun 4 2009, 06:43 PM dkjens A friend of mine had a Mitsubishi GT3000 (regular ... Jun 4 2009, 07:05 PM RJMII
A friend of mine had a Mitsubishi GT3000 (regular... Jun 4 2009, 09:13 PM RJMII working on bumper fitment...
This thing was a pa... Jun 4 2009, 08:57 PM RJMII My brakes are installed, adjusted, and bled! N... Jun 16 2009, 06:41 PM RJMII where it's sitting right now. =o) on the groun... Jun 16 2009, 06:47 PM RJMII While I was working on the brakes I came across an... Jun 16 2009, 06:51 PM neo914-6
While I was working on the brakes I came across a... Jun 17 2009, 02:12 AM RJMII One last shameless plug for PMB... lol
My new cl... Jun 16 2009, 06:52 PM ghuff This thread is full of total fucking win.
:weld... Jun 16 2009, 08:39 PM RJMII you see how I've got the rotor mounted backwar... Jun 17 2009, 03:00 AM RJMII removing spot welds and peeling off that 76 bumper... Jun 18 2009, 05:27 PM RJMII I had to put the bumper on to see just how bad the... Jun 18 2009, 05:28 PM RJMII Yes, the hammer is holding the bumper on. Just the... Jun 18 2009, 05:29 PM RJMII I got some of that bondo chiseled off... time to f... Jun 19 2009, 10:43 PM JRust Dude I would seriously consider replacing that fro... Jun 19 2009, 11:11 PM RJMII The one on the parts car is in a whole lot better ... Jun 20 2009, 10:31 AM RJMII got a little done on the car today. Changed the cl... Jun 20 2009, 11:17 PM RJMII oh, I also finished installing all of the new fuel... Jun 20 2009, 11:18 PM RJMII making holes... Jun 22 2009, 09:02 PM RJMII from the inside Jun 22 2009, 09:03 PM RJMII bigger holes Jun 22 2009, 09:04 PM RJMII from the inside Jun 22 2009, 09:05 PM RJMII My wife got a picture of my dad and I getting the ... Jun 22 2009, 09:10 PM |
11 User(s) are reading this topic (11 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st February 2025 - 09:43 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.