 Pulling hubs into rear bearings...need some advice |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| computers4kids |
 Sep 28 2008, 10:30 PM
Post
#1
|
|
Love these little cars!  Group: Members Posts: 2,443 Joined: 11-June 05 From: Port Townsend, WA Member No.: 4,253 Region Association: None  |
I've been converting my project car from 4 to five lug and have run into a snag. After installing new bearings in the rear, I attempted to draw the rear hubs into the bearing using the tool below. No matter how careful I am, the hub starts to go in crooked so I stop, not wanting to force it it.
So what's the trick to getting these puppies started straight? It seemed like an easy enough task. I do have the rear arms mounted, thinking it would be better held in place. Would pulling the arms and having the laying flat be any better. Thanks Attached image(s) 
|
   |
 
|
  |
Replies
| Justinp71 |
Jul 17 2009, 02:24 PM
Post
#2
|
|
Senior Member Group: Members Posts: 1,602 Joined: 11-October 04 From: Sacramento, CA Member No.: 2,922 Region Association: None 
|
I was also told that you should put some oil between the surfaces, because when the parts go back to the normal temps you'll trap some condensation in there...
|
|
|
|
Posts in this topic
computers4kids Pulling hubs into rear bearings...need some advice Sep 28 2008, 10:30 PM
roadster fan Hey Mark,
You have the right idea on the tool. I... Sep 28 2008, 11:06 PM
computers4kids
Hey Mark,
You have the right idea on the tool. ... Sep 28 2008, 11:26 PM Eric_Shea Spin it. Find the high side.
Lightly Tap-tap wit... Sep 28 2008, 11:30 PM sww914 I freeze the hubs and warm up the inner races to a... Sep 28 2008, 11:38 PM zambezi
I freeze the hubs and warm up the inner races to ... Sep 28 2008, 11:48 PM Cap'n Krusty
I freeze the hubs and warm up the inner races to... Sep 29 2008, 10:08 AM r_towle
I freeze the hubs and warm up the inner races to... Sep 29 2008, 10:50 AM computers4kids
I freeze the hubs and warm up the inner races to ... Sep 29 2008, 08:37 AM URY914 I always freeze my hubs. Sep 29 2008, 08:55 AM sww914 What kind of Pot Pies? It's very important not... Sep 29 2008, 09:33 AM Phoenix-MN Looks like the hubs have been plated, is the beari... Sep 29 2008, 10:17 AM roadster fan That's a good point. The machined surfaces if... Sep 29 2008, 10:51 AM computers4kids This picture is not my hub--just used because it i... Sep 29 2008, 06:53 PM jim_hoyland When I did mine, the side I heated with the map ga... Sep 29 2008, 08:11 PM Lou W
When I did mine, the side I heated with the map g... Sep 29 2008, 10:52 PM sww914 If your wife grows accustomed to hubs in the freez... Sep 29 2008, 10:54 PM computers4kids
What kind of Pot Pies? It's very important no... Sep 30 2008, 12:54 AM Derek Seymour Hey Mark did you use a torch as well or just the t... Jul 17 2009, 01:34 PM computers4kids
Hey Mark did you use a torch as well or just the ... Jul 17 2009, 02:16 PM Borderline
Hey Mark did you use a torch as well or just the... Jul 17 2009, 02:34 PM roadster fan Way to go Mark, glad it worked out for you. When ... Sep 30 2008, 01:44 AM sww914 :Qarl: :cheer: :headbanger: :DRUNK: :sleep: Sep 30 2008, 02:27 AM jmill
If your wife grows accustomed to hubs in the free... Jul 17 2009, 03:28 PM r_towle you need the right type of oil.... Jul 17 2009, 08:05 PM 9146986 I use a white scotchbrite disc on a roloc to polis... Jul 18 2009, 12:55 PM |
8 User(s) are reading this topic (8 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 23rd November 2024 - 01:47 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.