 Stuck in Gear, new trans stuck in 5th gear |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| astronomerdave |
 Sep 15 2009, 03:02 AM
Post
#1
|
|
Member  Group: Members Posts: 69 Joined: 26-January 09 From: Los Angeles, CA Member No.: 9,979 Region Association: Southern California  |
I just bought a newly rebuilt side shifter to upgrade my '72 tail shifter. Upon initial assembly of the shift linkage I had the trans in N, let the cabin shift lever find its place left-to-right (which was mostly upright), held it centered front-to-back, and tightened the bolt on the forked part under the shifter plate.
I shifted into R, backed out, then 1, and took it for a test drive. 1-2-3 no problem. But I couldn't find 4th gear; it looked like the shifter wasn't moving over far enough. So I figured it was just a simple shifter adjustment. Back in the garage I loosened the adjustment bolt, moved the shifter over a bit, and re-tightened. Sitting stationary in the garage I checked R-1-2-3-4-5 and then it was stuck. I couldn't move it at all at that point. (I actually thought it was stuck in 4th but now that I look at it, it could be 5th.) I removed the linkage and tried grabbing the little input shaft arm right on the trans but I cannot move it. There is a little bit of front-to-back play but not enough to change gears and no up-down movement. The questions: 1) Should this be possible and how is this possible to get stuck in gear? 2) Can I remedy this at home? The place I bought it offered to pay for shipping both ways so they'll take care of me if I have to do that. They suggested I first try to remove the two nuts securing the cover around the input shaft on the side and move some kind of fork in/out of some kind of detent. Not being a transmission guy I don't quite understand what I'm looking for. Plus, as I suspect, if the shift arm can't move whatever it is, how can I do this with my finger? I did remove this and pulled out the input shaft with its attached three-tanged arm, but not sure how to proceed now. Thanks... |
   |
 
|
  |
Replies
| jcd914 |
Sep 15 2009, 01:36 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 2,081 Joined: 7-February 08 From: Sacramento, CA Member No.: 8,684 Region Association: Northern California |
It sounds like you need to drop it out and drain it and take it over to the SOCAL Dr.Evil Trans clinic this weekend and get the forks adjusted properly.
http://www.914world.com/bbs2/index.php?s=&...t&p=1181332 Jim |
|
|
|
Posts in this topic
astronomerdave Stuck in Gear Sep 15 2009, 03:02 AM
Gint :bump: because I have a trans that's in exact... Sep 15 2009, 07:58 AM ClayPerrine The side shifter fork for the 4-5 gears is mis-adj... Sep 15 2009, 08:11 AM scrz914
Yep. You can wail on the shifter with a hammer, ... Sep 15 2009, 11:55 PM astronomerdave here's a video of the movement I have:
fdJMAPA... Sep 16 2009, 12:43 AM astronomerdave a few photos looking inside after removing shift c... Sep 16 2009, 12:49 AM
914OUTLAW Having the same issue and I'm to figure out to... Nov 18 2016, 03:32 PM r_towle In the bottom of the last picture you will see the... Sep 16 2009, 06:35 AM stugray Stupid question BUT -
There WAS fluid in there whe... Nov 18 2016, 04:54 PM 914OUTLAW Yes there was fluid. It all drained out after open... Nov 18 2016, 06:14 PM 914OUTLAW I guess I'll try prying the shift fork back in... Nov 18 2016, 08:10 PM 914OUTLAW No luck moving it into neutral. Anyone know how to... Nov 19 2016, 05:22 PM 914OUTLAW Here are the pictures of what mine looks like. Any... Nov 23 2016, 06:54 PM stugray Slide the brass shift fork (top center of first ph... Nov 23 2016, 10:19 PM |
6 User(s) are reading this topic (6 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 27th December 2024 - 06:53 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.