 Crank Position Sensor, for stock cooling engines |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| McMark |
 Jul 13 2009, 10:11 AM
Post
#1
|
|
914 Freak!  Group: Retired Admin Posts: 20,179 Joined: 13-March 03 From: Grand Rapids, MI Member No.: 419 Region Association: None  |
Since quite a few people were interested in crank fire and aftermarket FI system I finally finished up my crank position sensor setup. So if you want to run distributor-less ignition or modern FI, this setup is the ONLY setup built specifically to bolt onto a Type 4.
It's a complete bolt on upgrade, which means no drilling or modifying any parts to make this work. Only the cooling fan needs to be removed to complete the installation. This setup is great for modern FI system, which need a 'trigger signal'. Fuel only setups usually get their signal from the coil firing, but that signal is DIRTY and unreliable. This crank fire setup is smooth and clean. You can't beat it. There is no other setup built specifically for our motors. Quick easy installation with no headaches. Complete package price is $175 and includes the trigger wheel, the sensor w/ connector (pigtail or uncrimped), and the mounting bracket. You won't need to go searching for anything else. (IMG:http://www.914world.com/bbs2/uploads/post-419-1244942673.jpg) (IMG:http://www.914world.com/bbs2/uploads/post-419-1245008370.jpg) |
   |
 
|
  |
Replies
| McMark |
Feb 5 2010, 02:33 PM
Post
#2
|
|
914 Freak! Group: Retired Admin Posts: 20,179 Joined: 13-March 03 From: Grand Rapids, MI Member No.: 419 Region Association: None |
QUOTE The Ford EDIS ignition module is designed to work with a 36 tooth wheel, with 1 missing tooth to act as a synchronization reference for engine Top Dead Center. Which means my sensor works great for this. Relying on Jake's experience with the Mechanical Advance ONLY Mallorys, I would say that you probably won't need any load sensing. Just approximate the Mallory curve into the MegaJ software and it should act like you've got a Mallory installed. If you want to use load sensing, I would opt for vacuum based sensing. The TPS is more work to install and is a rather indirect way to approximate load. |
|
|
|
Posts in this topic
McMark Crank Position Sensor Jul 13 2009, 10:11 AM
rdauenhauer I want one of these!
What about a harness/con... Jul 13 2009, 01:13 PM
McMark
I want one of these!
What about a harness/co... Jul 17 2009, 10:56 AM JazonJJordan :trophy: Excellent work- McMark! I will get o... Jul 15 2009, 10:04 AM euro911 :beer2: Very nice, but a question comes to mind:
... Jul 16 2009, 12:05 AM McMark How do you deal with the added thickness? ... will... Jul 17 2009, 10:58 AM hcdmueller The trigger wheel is machined to be the correct th... Jul 16 2009, 08:01 AM euro911 So the sensor replaces the trigger points in the d... Jul 21 2009, 11:50 PM McMark This sensor is a key component of installing after... Jul 24 2009, 02:15 PM JazonJJordan
This sensor is a key component of installing afte... Jul 24 2009, 09:34 PM euro911
This sensor is a key component of installing afte... Jul 25 2009, 04:16 AM McMark I'm trying to motivate my genius EE into devel... Jul 24 2009, 09:39 PM rdauenhauer Does the placement of the Pickup preclude the use ... Sep 19 2009, 01:30 AM McMark I think it might interfere with the return line. ... Sep 19 2009, 01:36 AM rdauenhauer Perhaps if it was moved to the case pinch bolt jus... Sep 26 2009, 12:02 AM LotusJoe Is your trigger system still avail.?
Thanks
Joe
S... Dec 8 2009, 04:51 PM McMark Yes it is. Dec 8 2009, 05:19 PM ConeDodger Since this WOULD be the perfect solution for me, i... Dec 16 2009, 11:17 AM McMark Looks like SDS is 'working on' toothed whe... Dec 16 2009, 09:15 PM arvcube dont their systems currently work on magnetic trig... Dec 16 2009, 11:09 PM Mark Henry
dont their systems currently work on magnetic tri... Feb 5 2010, 11:22 AM McMark Yup, SDS uses a hall effect sensor, which relies o... Dec 16 2009, 11:34 PM draganc
Yup, SDS uses a hall effect sensor, which relies ... Jan 21 2010, 09:07 PM McMark My system only works with MegaSquirt for sure. It... Jan 22 2010, 12:43 AM underthetire
My system only works with MegaSquirt for sure. I... Jan 22 2010, 10:17 AM draganc Thanks McMark,
Do you offer a complet kit (HW, Me... Jan 22 2010, 06:54 PM McMark
My system only works with MegaSquirt for sure. ... Jan 27 2010, 02:55 PM McMark I have a complete fuel injection system that is al... Jan 27 2010, 02:53 PM underthetire Check here http://www.whiteproducts.com/metri-pac... Jan 27 2010, 03:49 PM jd74914 You can get Delphi WeatherPak connectors from Wayt... Jan 28 2010, 04:35 PM McMark This connector is not any of the (seems like hundr... Jan 28 2010, 04:40 PM typ4
This connector is not any of the (seems like hund... Jan 28 2010, 11:05 PM arvcube x2 on the question about what the sensor is off of... Jan 29 2010, 01:00 AM typ4
x2 on the question about what the sensor is off o... Jan 29 2010, 11:14 AM arvcube
x2 on the question about what the sensor is off ... Jan 29 2010, 02:40 PM jimkelly for megasquirt II per - http://www.megamanual.com/... Feb 6 2010, 01:46 PM McMark The adjustment in MegaTune is super easy and I can... Jan 30 2010, 12:30 AM McMark Rich, I've looked at relocating the sensor for... Feb 2 2010, 11:03 PM jimkelly for ignition only (using carbs) - what is needed?
... Feb 5 2010, 06:58 AM arvcube i may be needing one of these pretty soon. are the... Oct 28 2010, 11:20 PM McMark They are still available. I'm having more whe... Nov 10 2010, 01:54 PM arvcube
They are still available. I'm having more wh... Nov 10 2010, 04:16 PM rdauenhauer Mark any more work on that full-flow config? Nov 11 2010, 12:48 AM McMark Rob needs one now too, and his motor is here at th... Nov 11 2010, 05:25 PM tracer McMark, take a look at these suppliers. Might help... Dec 3 2010, 02:42 PM McMark Thanks for the tip. That's gonna take me whil... Dec 3 2010, 02:48 PM arvcube
Thanks for the tip. That's gonna take me whi... Dec 3 2010, 03:12 PM rdauenhauer
Rob needs one now too, and his motor is here at t... Dec 17 2010, 03:04 AM ConeDodger
Rob needs one now too, and his motor is here at ... Dec 17 2010, 06:15 PM rdauenhauer My plans are to utilize it w/ a Ford /4 EDIS setup... Dec 18 2010, 01:33 PM McMark
My plans are to utilize it w/ a Ford /4 EDIS setu... May 26 2011, 10:42 AM draganc
"... The plate mounts securely to the oil co... Jun 18 2011, 07:02 PM McMark I finally found connectors for this. So these are... Mar 14 2011, 05:50 PM Mike914 Mine came today, had a few minutes free so put it ... Apr 1 2011, 01:25 AM 1973_1.7 Great product, I have been looking for at trigger ... May 20 2011, 02:59 AM McMark I happen to have a DTM equipped engine in the shop... May 20 2011, 02:02 PM 914Mike
I happen to have a DTM equipped engine in the sho... May 23 2011, 12:54 AM McMark Okay, finally had a few minutes to try all this ou... May 26 2011, 10:32 AM 914Mike
...
I'll make a final check this afternoon a... May 28 2011, 05:12 PM McMark Sensor is a tight fit. I expect it will work fine... May 31 2011, 06:41 PM Krank
Sensor is a tight fit. I expect it will work fin... Jun 20 2011, 12:07 AM McMark I found the connector and now include them in the ... Jun 20 2011, 01:04 AM 1973_1.7 Do you sell just the trigger wheel? Price? Jun 23 2011, 03:36 PM John Jentz Mark, are these CPS's still avaliable? Are yo... Nov 23 2011, 12:30 PM McMark Yeah, they are still available. I'll shoot a ... Nov 23 2011, 12:35 PM John Jentz
Yeah, they are still available. I'll shoot a... Nov 25 2011, 02:58 PM flash914 <_< I can't find any info on the coil mo... Jan 23 2012, 12:46 PM McMark Flash, I haven't had time to set up my web-sto... Jan 23 2012, 02:23 PM draganc
Flash, I haven't had time to set up my web-st... Jan 25 2012, 09:56 AM McMark Dragan, I will get you a price. No word from Flash... Jan 27 2012, 12:32 AM flash914 Go ahead and let Dragan have it. Money set back, i... Jan 29 2012, 08:43 PM draganc
Go ahead and let Dragan have it. Money set back, ... Jan 30 2012, 09:50 PM 1973_1.7 You still have these kits? i would like to order o... Jul 18 2012, 01:24 AM McMark Yup, they're still available. But you should ... Sep 5 2012, 11:32 AM damo99 how much to ship one to australia
thanks Oct 1 2012, 04:07 AM flash914 Mark, new year new money. I need prices from you o... Jan 4 2013, 11:44 AM Jesco Reient Are these still available? I'm definitely look... Jan 28 2014, 09:21 AM |
34 User(s) are reading this topic (34 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 23rd November 2024 - 04:45 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.