 question on 911/914 stub axle, for subi conversion |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| ldscamaross |
 Mar 1 2010, 05:51 PM
Post
#1
|
|
Newbie  Group: Members Posts: 25 Joined: 31-January 08 From: south jordan utah Member No.: 8,646  |
hey all. im looking to get some axle stubs off of a 76-84 911. i am doing the subi tranny that porscharu is doing and i was trying to come up with anther way to adapt the cvs to the project. im using vw bus axles with the 100x6 bolt pattern which is what the magic flanges are set up for. the other side of the bus axle, the wheel side doesnt mate up to the 914 stub axle. i know you can just switch the cvs out but i was thinking of another rout. are there any years where the 911 had the 100x6 bolt pattern and the splines that match the 914 rear hubs. i have found pieces of info that would sugjest that the 76-84 stubs would work and ive seen some pics of them that looks like it would work. but i dont know for sure. does anybody know or has anybody looked at this? any info would be great. also i am intrested to buy them if anybody has them around.
thanks |
   |
 
|
  |
Replies
| ldscamaross |
Mar 3 2010, 12:59 PM
Post
#2
|
|
Newbie Group: Members Posts: 25 Joined: 31-January 08 From: south jordan utah Member No.: 8,646 |
i am using the bus axles because i am using the magic flanges with a subaru transmission. it is discussed ont the subaru transmission possibility thread. the bus axles are shorter but they need to be because the subi tranny is a little wider. does anybody know if the 911 stub axle will slide into the 914 rear hub?
|
|
|
|
| pcar916 |
Mar 4 2010, 10:58 AM
Post
#3
|
|
Is that a Lola? Group: Members Posts: 1,523 Joined: 2-June 05 From: Little Rock, AR Member No.: 4,188 Region Association: None 
|
QUOTE(ldscamaross @ Mar 3 2010, 10:59 AM)  i am using the bus axles because i am using the magic flanges with a subaru transmission. it is discussed ont the subaru transmission possibility thread. the bus axles are shorter but they need to be because the subi tranny is a little wider. does anybody know if the 911 stub axle will slide into the 914 rear hub? Early 911 stub axles (circa '69. I don't know about the '70) fit perfectly and use the 911 cv's as well. This assumes you have already converted to or already have 5-bolt hubs. When I was researching this last fall I had a very hard time finding the early CV's though. Anybody know where to get them now, and the early 911 stub axles? I haven't checked since then, but I won't be able to use my 914-6 stub axles at that point. With that solution you have to have either 914-6 axles with the shoulder turned to accept the thicker CV, or go with SwayAway or something like it. But it let's you use 930 CV's inboard if you have those transmission flanges. |
|
|
|
Posts in this topic
ldscamaross question on 911/914 stub axle Mar 1 2010, 05:51 PM
strawman Can't help you -- I'm using the 108mm stub... Mar 1 2010, 07:24 PM 914Sixer You might try getting a set of early (65-68) 911 s... Mar 1 2010, 07:43 PM BIGKAT_83
That will permit me to use the 930-style CVs. My... Mar 1 2010, 08:26 PM stock93 BigKat, Who resplined them for you? I've been ... Mar 2 2010, 07:17 PM
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 6th January 2025 - 03:16 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.