 Jack Post Repair Question |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| saigon71 |
 May 6 2011, 03:33 PM
Post
#1
|
|
Advanced Member  Group: Members Posts: 2,006 Joined: 1-June 09 From: Dillsburg, PA Member No.: 10,428 Region Association: MidAtlantic Region 
 |
I welded a new jack tube on to the replacement wheelhouse section from Restoration Design today, aligning it perfectly with the square hole that came pre-punched in the new panel. When I started fitting the jack post brace, I had to adjust the bends on it by about 1/8" to get it to fit right. I am having a hard time getting accurate measurements from the old chunk of long I have because it is a disaster.
The question is, how reliable is the pre-punched guide hole? Should I just roll with it? Anyone else run into something similar? Thanks in advance. Pics:     |
   |
 
|
  |
Replies
| tomeric914 |
May 7 2011, 07:25 AM
Post
#2
|
|
One Lap of America in a 914! Group: Members Posts: 1,263 Joined: 25-May 08 From: Syracuse, NY Member No.: 9,101 Region Association: North East States
|
I don't think your getting good weld penetration judging from the pictures. Looks kinda "boogery". Are you using a MIG with or without gas?
|
|
|
|
Posts in this topic
saigon71 Jack Post Repair Question May 6 2011, 03:33 PM
TargaToy Everything "reproduction" I ever buy req... May 6 2011, 07:48 PM
saigon71
Everything "reproduction" I ever buy re... May 6 2011, 11:00 PM rhcb914 Moving the bends 1/8 of an inch is NOTHING! Th... May 7 2011, 07:03 AM saigon71
I don't think your getting good weld penetrat... May 7 2011, 11:28 AM draganc
I don't think your getting good weld penetra... May 7 2011, 02:52 PM Spoke When I replaced the jack point on the passenger si... May 7 2011, 07:46 AM ppetion Nice , I have to do one of mine soon. May 7 2011, 12:58 PM TargaToy Hey, by the way. Did you know that wheelhouse sec... May 7 2011, 07:00 PM saigon71
Hey, by the way. Did you know that wheelhouse se... May 7 2011, 08:45 PM saigon71
Hey, by the way. Did you know that wheelhouse s... May 9 2011, 02:10 PM scotty b
Hey, by the way. Did you know that wheelhouse se... May 7 2011, 08:56 PM scotty b i normally put the long on then fit the jack post ... May 7 2011, 08:36 PM saigon71
i normally put the long on then fit the jack post... May 7 2011, 08:59 PM avidfanjpl I recommend ONLY Restoration Design from Canada... May 7 2011, 09:05 PM saigon71 Checked the fit of the outer fiberglass long with ... May 8 2011, 06:58 PM jaxdream
I welded a new jack tube on to the replacement wh... May 8 2011, 10:13 PM saigon71
I welded a new jack tube on to the replacement w... May 9 2011, 02:12 PM TargaToy Here's what the two pieces from RD look like. ... May 9 2011, 04:32 PM saigon71
Here's what the two pieces from RD look like.... May 9 2011, 05:25 PM retro74
Here's what the two pieces from RD look like.... Jul 21 2011, 07:54 PM retro74
Here's what the two pieces from RD look like... Jul 28 2011, 07:08 AM TargaToy I just wish somebody made the same wheelhouse part... May 9 2011, 08:15 PM saigon71
I just wish somebody made the same wheelhouse par... May 10 2011, 06:19 AM scotty b
I just wish somebody made the same wheelhouse par... May 10 2011, 05:35 PM peteyd The two pieces now come spot welded together
Jul 28 2011, 08:32 AM saigon71
The two pieces now come spot welded together
... Jul 28 2011, 01:56 PM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 31st October 2024 - 07:25 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.