 SOT: electrical gurus check in..., how to dim LEDs? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| dlo914 |
 Nov 30 2012, 12:45 AM
Post
#1
|
|
Whatchu' lookin' at?!?!  Group: Members Posts: 3,432 Joined: 6-September 04 From: San Gabriel, CA Member No.: 2,697  |
So i've retrofitted some LED rings into my daily driver, but i'm only using the LEDs as the running lights and using the filament bulb when brakes are applied. how would i go about using the LEDs for both running and braking light usage? i know i'm suppose to add a resistor to each positive LED wire, but i'm so confused as to what OHM rating or % etc i'm suppose to use. The guys at two radioshacks were useless.
Here's how they look at the moment: (IMG:http://www.914world.com/bbs2/uploads_offsite/i62.photobucket.com-2697-1354257938.1.jpg) |
   |
 
|
  |
Replies
| bperry |
Dec 1 2012, 12:29 PM
Post
#2
|
|
Lurker Group: Members Posts: 477 Joined: 16-February 04 From: Dallas, Tx Member No.: 1,661 |
Here is a link to a DIY article on how to wire up LEDs for DRL and turn signals that
uses resistors for brightness control. Rear Running Lights Mod It is a fancier version of the circuit that Tom drew up. --- bill |
|
|
|
Posts in this topic
dlo914 SOT: electrical gurus check in... Nov 30 2012, 12:45 AM
Tom LED brilliance is controlled by current flow. Curr... Nov 30 2012, 04:49 AM Tom Are these rings a plug in to the regular socket wh... Nov 30 2012, 05:58 AM Spoke For the brake light with higher intensity, as Tom ... Nov 30 2012, 08:26 AM Bartlett 914 I am doubtful that adding resistance will give sat... Nov 30 2012, 08:33 AM Nine_14 http://en.wikipedia.org/wiki/LED Nov 30 2012, 09:12 AM Tom Here is a simple led circuit than will allow the r... Nov 30 2012, 02:24 PM mr914 Temporary, or could be permanent...
Buy a variabl... Nov 30 2012, 03:04 PM Dave_Darling All the automotive LED taillights I know of blink.... Nov 30 2012, 05:23 PM
Spoke
If it were as simple as putting a resistor in lin... Nov 30 2012, 05:52 PM Spoke Here's a switching converter to efficiently dr... Nov 30 2012, 06:07 PM stugray There are off the shelf drivers that can do this.
... Nov 30 2012, 07:34 PM Spoke
There are off the shelf drivers that can do this.... Nov 30 2012, 07:51 PM nukepipe
So i've retrofitted some LED rings into my da... Nov 30 2012, 08:42 PM aircooledtechguy I'm probably missing something here, but if yo... Dec 1 2012, 12:09 AM falconfp2001 I would say you need to check this site out
http:... Dec 1 2012, 02:58 AM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 25th June 2024 - 08:40 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.