 Shrinkage ? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| cary |
 Mar 12 2013, 01:34 PM
Post
#1
|
|
Advanced Member  Group: Members Posts: 3,900 Joined: 26-January 04 From: Sherwood Oregon Member No.: 1,608 Region Association: Pacific Northwest 
 |
We're getting ready to move the project off the rotissere to the lift.
We'd rehung the doors . Pretty scary hanging there on the rotissere. How many 100's should we allow for shrinkage when we reinstall the long? |
   |
 
|
  |
Replies
| cary |
Mar 20 2013, 10:05 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 3,900 Joined: 26-January 04 From: Sherwood Oregon Member No.: 1,608 Region Association: Pacific Northwest
|
Here's the door gap measurement rods in use.
 Top one .............fits perfect.  Now we go to measure the 1039mm measurement at the door latch. One has to be smarter than a 5th grader. Considering both planes are at an angle where is the correct spot to measure? With the door gap set a 5mm. Mine measures right in the middle of the radius. |
|
|
|
| cary |
Mar 24 2013, 08:58 AM
Post
#3
|
|
Advanced Member Group: Members Posts: 3,900 Joined: 26-January 04 From: Sherwood Oregon Member No.: 1,608 Region Association: Pacific Northwest
|
QUOTE(cary @ Mar 20 2013, 09:05 PM)  Here's the door gap measurement rods in use. Top one .............fits perfect. Now we go to measure the 1039mm measurement at the door latch. One has to be smarter than a 5th grader. Considering both planes are at an angle where is the correct spot to measure? With the door gap set a 5mm. Mine measures right in the middle of the radius. Still looking for an answer on the bottom measurement............... I was just thinking. Has anyone every seen a stash of the factory body repair jigs? We've all seen the pictures out of the factory manual set. But have we seen the pieces in the flesh(metal)? |
|
|
|
Posts in this topic
cary Shrinkage ? Mar 12 2013, 01:34 PM
rick 918-S Shrinkage is not required or desired. :ttiwwp: Mar 12 2013, 04:32 PM
cary Took lots of pictures on my camera that l'll p... Mar 12 2013, 05:28 PM scotty b Weld slowly, mocve around, not in one direction, a... Mar 12 2013, 08:20 PM cary Here's the pictures I promised.
Put the doo... Mar 12 2013, 09:02 PM SirAndy This is where I ended up even with the door brace ... Mar 12 2013, 09:06 PM cary
Moving from the rostissere to the lift.
The ... Mar 12 2013, 09:09 PM cary
Almost getting there on the passenger side. But... Mar 12 2013, 09:16 PM cary Here's the drivers side.
Mar 12 2013, 09:18 PM cary I do have adjustable door braces. I can move the d... Mar 12 2013, 10:18 PM cary Got up early to finish reading this post.
http://w... Mar 13 2013, 07:28 AM SirAndy I'm just seeking perfection on a tub that most... Mar 13 2013, 11:25 AM ThePaintedMan
While the door gaps are important and visually an... Mar 13 2013, 11:42 AM sixnotfour Better measure the windshield to targa bar also, T... Mar 13 2013, 12:11 PM cary Time for lunch.
Feel much better now.
Both doors ... Mar 13 2013, 02:42 PM cary Here's the pictures from today.
Drivers s... Mar 13 2013, 10:07 PM cary Here's the suspension point jig we built.
Bolt... Mar 13 2013, 10:12 PM cary Tomorrow we'll install the drivers long after ... Mar 13 2013, 10:25 PM rick 918-S get the drivers door gap
closed up around 5mm max... Mar 13 2013, 11:37 PM Jeff Hail There is a lot of good feedback and direction here... Mar 14 2013, 01:33 AM cary After seeing how much the front 1/2's can move... Mar 14 2013, 09:30 AM mskala
...
I do believe we'll create some sort of br... Mar 15 2013, 12:01 PM cary It didn't happen. We're still tinkering. S... Mar 15 2013, 08:57 AM cary Got tired of nicking the paint (whats left of it) ... Mar 15 2013, 08:59 AM cary Here's the body supported on the lift.
Mar 15 2013, 09:01 AM cary Here's the measurement tools I created for mea... Mar 15 2013, 09:03 AM SirAndy I think you're doing good. Can't wait to s... Mar 15 2013, 11:21 AM 3d914 That's a very challenging restoration. Impress... Mar 15 2013, 01:28 PM cary
Its really more about the tub flexing when you f... Mar 15 2013, 02:30 PM worn
Its really more about the tub flexing when you ... Mar 19 2013, 10:46 AM cary I've already crushed one. When they're gon... Mar 19 2013, 09:29 PM cary The long is finally installed. :D
The car is ... Mar 20 2013, 10:16 PM cary Body movement
nBDTWFJWX3I
That was easy Mar 20 2013, 11:27 PM |
18 User(s) are reading this topic (18 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 27th December 2024 - 10:19 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.