![]() |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
![]() |
stewteral |
![]()
Post
#1
|
Old Member ![]() ![]() Group: Members Posts: 384 Joined: 4-December 07 From: Camarillo, CA Member No.: 8,424 Region Association: Southern California ![]() |
![]() ![]() ![]() For SALE: Porsche 914 Chevy V8 conversion car, $35k invested +, Price $16,500, certified funds -11.0 second Qtr Mile -Built 383 Chevy SBC, output 500 HP, 4-bolt Mains -Comp Cams Roller-cam, pushrods and hydraulic lifters -Eagle 4130 crank -Eagle forged rods -10:1 Keith Black Hypereutectic pistons -All parts balanced with harmonic balancer -Stainless steel rockers -Aluminum heads -MSD Distributor & Ignition system -Edelbrock aluminum intake manifold -750 Holley 4-barrel Carb -Custom aluminum valve covers -180-degree headers -Dual mufflers w/ Super-Trapps + Open pipe replacement for track days -Canton Road Race baffled oil pan -Canton 3Qt Accusump -Dual oil coolers with fans -All oil & fuel lines are Aeroquip -Remote Meziere electric water pump – 55 GPM -Camaro Aluminum radiator with dual fans -Spare Chevy 4-bolt mains block -Transmission: Porsche Turbo 930 4-spd trans with custom shift linkage -Quaife Torsen Limited slip differential -Turbo Porsche half-shafts and CV joints -Custom flywheel with Porsche clutch -Wilwood Hydraulic clutch master cylinder & peddle -Wilwood Hydraulic clutch slave cylinder with Aeroquip flex-line -Chassis: the ONLY race track developed suspension conversion car now running including spring rates, swabars, shocks, chassis squared adjustments and bump-steered. -Custom Dash: Porsche Tach, VDO Water temp, oil temp, oil pressure gages, Oil pressure & alternator warning LEDs. -Transmission oil temp gage -Full rollcage -Racing seats -5-belt racing seat belts (driver) -4-belt racing seat belts (passenger) -Racing Engineer tuned spring rates -Custom front and rear swaybars -Koni adjustable Sport front shocks -Custom built dual adjustable Koni rear shocks -Spare rear springs -Rear suspension bracing for track cornering loads -Removable rear wing for track -Rennspeed fiber glass fender flares, rocker panels and nose piece with splitter -Custom fiberglass side cooling scoops to Engine Compartment -Brakes: Wilwood 12” x 1.25” vented rotor, all wheels -Wilwood 4-piston Aluminum Calipers, all wheels -Aeroquip brake lines -Wilwood Dual master cylinder w/ balance bar aluminum peddle -Remote brake & clutch reservoirs in front trunk -Street Wheels: 8” steel rims with TA Radials (street) Track Wheels: 9-1/2” front Aluminum wheels w/ Fresh Goodyear racing slicks (track) Track Wheels: 11” rear Aluminum Wheels w/ Fresh Goodyear racing slicks (track) Documentation: 3” - 3-ring binder of Every part of the Chassis 3” - 3-ring binder of Every part of the engine. 3” - 3-ring binder of complete 930 trans shop manual 2” – 3-ring binder all about the Holley Carb w/ 2 shop manuals. 1” – 3-ring binder: Complete data support for all chassis and tire on-track settings. Track Support: Seller will attend buyer’s initial track event to help in learning the car at The Streets of Willow Springs A custom towbar is also available. To see the car in action here is the url for my last outing at Buttonwillow. It was interesting that I was following the yellow Serious NASCAR competitor with a 650HP Chevy. I was very satisfying to be able to pull him on the straights. Now, of course, the excuses: -First lap was slow and slippery in getting the slicks up to temp on that always greasy track. Note the tail stepping out in the 1st right-hand corner. -This was my first time to run the track CW and I never felt I had the lines down, was not comfortable and couldn't get into a rhythm. Thus missing shifts and totally blowing my braking point at the end to the start straight. Ah shucks! -For some dumb reason, I was black flagged on that last lap. It turned out to be corner worker error....not that unusual at these open track days. Still, the car ran great and was a kick-in-the-pants to drive. http://www.youtube.com/watch?v=oeeWoJZm9C4 Terry, Camarillo, CA 805-482-0322 |
![]() ![]() |
sean_v8_914 |
![]()
Post
#2
|
Chingon 601 ![]() ![]() ![]() ![]() Group: Members Posts: 4,011 Joined: 1-February 05 From: San Diego Member No.: 3,541 ![]() |
I have enjoyed watching you up at Streets
|
![]() ![]() |
![]() |
Lo-Fi Version | Time is now: 13th February 2025 - 01:11 PM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |