 Fabbed Heat Exchangers for some Headers, Hope this works |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| DNHunt |
 Aug 8 2004, 03:54 PM
Post
#1
|
|
914 Wizard? No way. I got too much to learn.  Group: Members Posts: 4,099 Joined: 21-April 03 From: Gig Harbor, WA Member No.: 598  |
I spent the weekend cutting and welding heat exchangers for some headers I got from Bleyseng. I guess these are Eurorace that Zois had, then, Brad then, Geoff and now me. Anyway they are stainless and I used 304 stainless for the jackets.
Hope this works cause I barely left the garage and I used up the last few car tokens I had with the wife. Dave Attached image(s) 
|
   |
 
|
  |
Replies
| bperry |
Aug 10 2004, 12:08 AM
Post
#2
|
|
Lurker Group: Members Posts: 477 Joined: 16-February 04 From: Dallas, Tx Member No.: 1,661 |
Looking at those headers, I don't think that they are Eurorace headers.
I did have some like those but the ones that I have now, I'm pretty sure that they are the Eurorace headers, are not like that. (I actually got them from FAT years ago) Mine are exactly the same as the ones in this picture: (including muffler) http://www.914world.com/bbs2/index.php?act...t=ST&f=2&t=8519 The pipes never go under the bottom of the case like these. In the ones I have, the #3 and #4 tubes curve away from the engine not towards/under it and the #2 tube crosses over behind the engine not under it. Did Eurorace make different versions? Which of these is the real Eurorace, vs Triad, vs ??, etc..? --- bill |
|
|
|
Posts in this topic
DNHunt Fabbed Heat Exchangers for some Headers Aug 8 2004, 03:54 PM
DNHunt Here's another view Aug 8 2004, 03:59 PM thomasotten That doesn't look like you are going to get a ... Aug 8 2004, 04:34 PM Jeroen Let us know if or how well it works!
cheers,
... Aug 8 2004, 04:43 PM bperry Um... did you measure your clearance between the s... Aug 8 2004, 07:12 PM rdauenhauer I commend your ingenuity Dave but it dost look lik... Aug 8 2004, 07:47 PM 9146986 Hope it works! You didn't make the collec... Aug 8 2004, 09:46 PM Bruce Allert Dave... you never cease to amaze me :trophy:
(I ... Aug 8 2004, 11:20 PM rhodyguy are you going to build up some rectangular stock t... Aug 9 2004, 12:10 AM Brad Roberts Umm.. that is a ceramic coated header... NOT stain... Aug 9 2004, 03:16 AM maf914 Way to go Dave. I hope that works for you.
Tha... Aug 9 2004, 07:02 AM
DNHunt Well Brad you were right. The magnet sticks real g... Aug 10 2004, 07:32 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 28th June 2024 - 01:31 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.