 Gas Tank Adventures, Tank out, stripping paint... |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| boxsterfan |
 Sep 6 2014, 06:40 PM
Post
#1
|
|
914's are kewl  Group: Members Posts: 1,776 Joined: 6-June 03 From: San Ramon, CA Member No.: 791 Region Association: Northern California  |
So, I start the process of replacing my fuel pump today (which has been relocated up front by PO). So I got the tank out and it was starting to look pretty "rusty". So I figured I woul attempt to strip it down and repaint it. I have gotten most of the paint stripped off, but how am i going to get some/all of this surface rust off?
Any good radiator shops in San Ramon area I could drop it off to have someone finish it for me this week? Note: the inside of the tank looks very good....as if someone re-did the tank sometime ago. Attached thumbnail(s)  
|
   |
 
|
  |
Replies
| mepstein |
Oct 12 2014, 09:41 AM
Post
#2
|
|
914-6 GT in waiting Group: Members Posts: 19,707 Joined: 19-September 09 From: Landenberg, PA/Wilmington, DE Member No.: 10,825 Region Association: MidAtlantic Region 
|
Vinegar is cheap, works great and no noxious fumes or hazmats. If your not satisfied with your tanks paint job, I would take it to a body shop for a coat of epoxy.
|
|
|
|
| boxsterfan |
Oct 12 2014, 01:41 PM
Post
#3
|
|
914's are kewl Group: Members Posts: 1,776 Joined: 6-June 03 From: San Ramon, CA Member No.: 791 Region Association: Northern California |
QUOTE(mepstein @ Oct 12 2014, 08:41 AM)  Vinegar is cheap, works great and no noxious fumes or hazmats. If your not satisfied with your tanks paint job, I would take it to a body shop for a coat of epoxy. Tell me more about the epoxy coat? Is that just an epoxy primer and I would also need to have the body shop paint a coat over that? I might go the route of por-15 tank sealer also. But is that done before or after a paint job? If after, how do you keep the tank from flash rusting again? |
|
|
|
Posts in this topic
boxsterfan Gas Tank Adventures Sep 6 2014, 06:40 PM
boxsterfan Inside the tank. Sep 6 2014, 06:41 PM boxsterfan Tank stripped (as far as I could get today). Looki... Sep 6 2014, 06:43 PM Mike Bellis You need to find a powder coating shop. They can b... Sep 6 2014, 06:51 PM
boxsterfan
You need to find a powder coating shop. They can ... Sep 6 2014, 06:57 PM Jeff Bowlsby There is a shop in hayward...can't recall the ... Sep 6 2014, 06:55 PM Harpo You mentioned that the PO had possibly redid the t... Sep 6 2014, 06:58 PM boxsterfan Electro-Plating Specialties Incorporated
2436 Ame... Sep 6 2014, 07:04 PM Mike Bellis Most powder coating shops have a blaster... Sep 6 2014, 07:09 PM boxsterfan Being the CSOB 914 owner that I am, I was able to ... Sep 7 2014, 09:27 PM boxsterfan A question about the "fuel sock". So I p... Sep 7 2014, 09:32 PM patssle
However, I can't seem to get that nut off o... Sep 7 2014, 09:42 PM boxsterfan OK, I'm soaking it in WD40 for now. I have som... Sep 7 2014, 10:06 PM boxsterfan Well, after my CSOB attempt to repaint my tank and... Oct 11 2014, 10:21 PM Marty Yeoman :( Oct 11 2014, 10:59 PM Harpo I believe that both rotary and racer Chris have fu... Oct 12 2014, 05:42 AM bdstone914 I bought a bunch of extra crush washers from rotar... Oct 12 2014, 06:28 AM mepstein buy a gallon or 2 of apple cider vinegar. pour in ... Oct 12 2014, 07:26 AM cary I've been in about the same spot for a couple ... Oct 12 2014, 08:50 AM bdstone914 I have a couple of good clan late tanks. Hear are... Oct 12 2014, 12:13 PM boxsterfan Bruce, thanks for the message. I'm going to tr... Oct 12 2014, 12:53 PM mepstein
Bruce, thanks for the message. I'm going to t... Oct 12 2014, 01:05 PM bdstone914
Bruce, thanks for the message. I'm going to ... Oct 12 2014, 01:11 PM cary Another Google item.
As soon as you finish cleanin... Oct 12 2014, 07:19 PM |
14 User(s) are reading this topic (14 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 18th January 2025 - 11:08 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.