 Piston oil squirters for a /4...anyone have them? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Mueller |
 May 26 2003, 02:20 PM
Post
#1
|
|
914 Freak!  Group: Members Posts: 17,150 Joined: 4-January 03 From: Antioch, CA Member No.: 87 Region Association: None 
 |
Is the 150 dollar bill worth it? Would I need an external oil-cooler for sure since the oil would be hotter than normal without piston squirters?
|
   |
 
|
  |
Replies
| McMark |
Oct 26 2014, 07:04 PM
Post
#2
|
|
914 Freak! Group: Retired Admin Posts: 20,179 Joined: 13-March 03 From: Grand Rapids, MI Member No.: 419 Region Association: None |
911 squirters are often replaced as a peace-of-mind repair. AFAIK, the factory installed 911 squirters are pressed in from the bearing side so removal is just a matter or tapping them back out. The quick retrofit version is to dril from the case register, tap them in and peen them over. But you should be able to tap them out with a rod inserted from the bearing side of the hole.
I'll be doing it the factory way which leaves a little seat material to keep the squirters from popping out. |
|
|
|
Posts in this topic
Mueller Piston oil squirters for a /4...anyone have them? May 26 2003, 02:20 PM
Scott Mike,
You may want to check with FAT Performance.... May 26 2003, 02:23 PM Scott Hey Mike,
See Brad's post on his dyno room, a... May 26 2003, 02:29 PM Mueller Hey Scott,
i know of a few shops that'll ins... May 26 2003, 02:36 PM Bleyseng That was Bernie Bergman's experience on his tu... May 26 2003, 02:39 PM Brad Roberts Not worth it.
B May 26 2003, 02:41 PM Brad Roberts I'll *probably* persue a turbo kit. But I prom... May 26 2003, 02:43 PM Aaron Cox i read in hot vw's, that the type 1 crowd has ... May 26 2003, 03:02 PM Bleyseng Will it have the option of NOS?
Geoff May 26 2003, 03:02 PM Mark Henry Mike, if your rods are nice and tight on the shoul... May 26 2003, 05:08 PM MJHanna It depends on what your doing with the motor. I ha... May 27 2003, 06:59 AM Bleyseng This is the mods I have done, is this what you are... May 31 2003, 10:32 PM Brad Roberts I dont think that is what he is talking about..
H... Jun 1 2003, 01:03 AM Mark Henry With the 30mm pump he's planning on running th... Jun 1 2003, 05:10 AM Bleyseng Yes I did! But this is the pic I was looking f... Jun 1 2003, 09:06 AM seanery what pic? Jun 1 2003, 09:08 AM Bleyseng the one I posted previously. What the hell is all ... Jun 1 2003, 09:14 AM r_towle Brining this back up to the front of the line for ... Oct 26 2014, 08:23 AM McMark I've never seen the rod notch in person and I... Oct 26 2014, 11:58 AM
DBCooper
I've never seen the rod notch in person and I... Oct 27 2014, 06:55 AM McMark
I don't know why they wouldn't work. Pre... Oct 27 2014, 10:10 AM stugray isnt there also a mod that drills a very small hol... Oct 26 2014, 12:15 PM McMark Here's that mod.
The real Porsche squirters ... Oct 26 2014, 12:29 PM McMark Check valve opens around 20psi. Oct 26 2014, 12:31 PM r_towle
Check valve opens around 20psi.
Umm, not always ... Oct 26 2014, 06:23 PM Mark Henry I've cut notches in rods, I'd say it likel... Oct 26 2014, 06:42 PM wndsnd
911 squirters are often replaced as a peace-of-mi... Oct 26 2014, 07:21 PM Mark Henry
[quote name='McMark' post='2102942' date='Oct 26 ... Oct 27 2014, 04:04 AM JimN73 Somebody, Nate (aircoledtechguy), posted a photo o... Oct 26 2014, 07:08 PM Dave_Darling "Better", of course! But is the not... Oct 27 2014, 10:28 AM DBCooper Yeah, it would be great to know VW's engineeri... Oct 27 2014, 01:27 PM rudedude They might be great until your 6 cylinder isn... Oct 27 2014, 01:56 PM r_towle Seems doing this modification to the big end might... Oct 27 2014, 02:57 PM r_towle Interesting
Carrillo Rods do this modification als... Oct 27 2014, 03:01 PM McMark Took a look at a spare case today. Looks like a pr... Oct 27 2014, 10:54 PM r_towle From what I read, it is not straight...
A slight ... Oct 28 2014, 06:12 AM Racer Chris Notching the rods is simple and effective. Oct 28 2014, 07:05 AM aircooledtechguy
Notching the rods is simple and effective.
:ag... Oct 28 2014, 10:30 AM McMark
directing a portion of that splash where you want... Oct 28 2014, 06:44 PM r_towle One of the things I saw, which I can't seem to... Oct 28 2014, 06:05 PM aircooledtechguy
One of the things I saw, which I can't seem t... Oct 28 2014, 06:37 PM jcd914 I saw a you tube video where someone was machining... Oct 28 2014, 06:31 PM r_towle Interesting to look at the Carrillo rods.
They hav... Oct 28 2014, 06:34 PM Katmanken
Interesting to look at the Carrillo rods.
They ha... Oct 28 2014, 08:43 PM r_towle Carrillo cuts them offset also....figure they migh... Oct 28 2014, 06:38 PM Mark Henry Really that's all that matters... Oct 28 2014, 08:24 PM McMark
Really that's all that matters...
True, but ... Oct 28 2014, 10:15 PM Mark Henry
Really that's all that matters...
True, but... Oct 29 2014, 04:54 AM falcor75 If you want threaded squirters you can grab them f... Oct 29 2014, 05:09 AM |
7 User(s) are reading this topic (7 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 12th January 2025 - 08:07 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.