 Distributor Pull, /6 |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| EdwardBlume |
 Nov 1 2015, 10:26 PM
Post
#1
|
|
914 Wizard  Group: Members Posts: 12,338 Joined: 2-January 03 From: SLO Member No.: 81 Region Association: Central California 
 |
I need to pull the distributor on the 2.4 /6, but it won't come out. I have it at TDC #1, with the rotor pointing at 1. Took the bolt off the adjuster and can move it back and forth, but the whole assembly will not come up and out.
Any ideas? |
   |
 
|
  |
Replies
| kconway |
Nov 2 2015, 03:04 PM
Post
#2
|
|
Senior Member Group: Members Posts: 1,347 Joined: 6-December 04 From: Monrovia, CA Member No.: 3,231 Region Association: Southern California |
Rob,
As I mentioned, that distro was reworked/rebuilt by Barry Hershon at flat6recurve.com/. He advanced the timing to account for carbs and completely rebuilt the thing. I'm very surprised the advance plate is sticking. What I don't remember is if I had it set up for points or not. Kev |
|
|
|
| EdwardBlume |
Nov 2 2015, 07:27 PM
Post
#3
|
|
914 Wizard Group: Members Posts: 12,338 Joined: 2-January 03 From: SLO Member No.: 81 Region Association: Central California
|
QUOTE(kconway @ Nov 2 2015, 01:04 PM)  Rob, As I mentioned, that distro was reworked/rebuilt by Barry Hershon at flat6recurve.com/. He advanced the timing to account for carbs and completely rebuilt the thing. I'm very surprised the advance plate is sticking. What I don't remember is if I had it set up for points or not. Kev Yeah, it's totally sticking. Virtually undrivable. Coming off of throttle it takes anywhere from 2-6 seconds to drop to idle. Weak springs? No dust shield either. You had it set up for Petronix but I went back to points. |
|
|
|
Posts in this topic
RobW Distributor Pull Nov 1 2015, 10:26 PM
matthepcat Crowbar and a rubber hammer?
I have seen some ren... Nov 1 2015, 11:31 PM porschetub
I need to pull the distributor on the 2.4 /6, but... Nov 2 2015, 01:41 AM
Mike Bellis
You had it set up for Petronix but I went back to... Nov 2 2015, 10:14 PM colingreene Mine took a small bar and some intense wiggling. T... Nov 2 2015, 04:26 PM RobW Runs fine otherwise though specially after the car... Nov 2 2015, 07:29 PM r_towle Did you possibly use a screw that is too long for ... Nov 2 2015, 07:36 PM RobW
Did you possibly use a screw that is too long for... Nov 2 2015, 09:57 PM r_towle It's not the advance, it's the two plates ... Nov 2 2015, 10:01 PM colingreene Mike, I have had no problemi with points.
In fact... Nov 5 2015, 01:32 AM mskala For somebody handy with a soldering iron, you can ... Nov 5 2015, 07:04 AM bcheney
For somebody handy with a soldering iron, you can... Nov 5 2015, 03:33 PM mskala
[quote name='mskala' post='2261272' date='Nov 5 2... Nov 6 2015, 07:19 PM |
10 User(s) are reading this topic (10 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 14th January 2025 - 06:15 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.