 Steering rack rebuild, seal and bearing numbers |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Olympic 914 |
 Jan 8 2016, 09:09 AM
Post
#1
|
 Group: Members Posts: 1,707 Joined: 7-July 11 From: Pittsburgh PA Member No.: 13,287 Region Association: North East States 
 |
Thought I would install my Turbo tie rod ends and found that one of the rack end bushings had stuck to the rack and pushed it out. ( probably during storage )
I found a rack rebuild thread by Wes V http://www.914world.com/bbs2/index.php?showtopic=95747 But it seems his rack is different than mine. his is a 75 mine is a 73 . I didn't know they changed them. So it looks like I will have to disassemble my rack and clean up / polish the rack rod. problem is I can't seem to find a number for the seal. Part #10 in diagram  Also the 911 rack ( and later 914 rack ? ) has a needle bearing at the top whereas, it looks like the 73 rack has caged ball bearings top and bottom. My rack part number is 914.347.014.00 I haven't disassembled mine yet. Does anyone have part numbers for the bearings and the seal? are the caged rollers the same number as in the 911 rack? # 6202. and if I can't find the seal could I just go with a sealed 6202 bearing (if available) on the top and skip the #10 seal? I put PB blaster on the stuck end bushing last night and will work on it later today. |
   |
 
|
  |
Replies
| r_towle |
Feb 5 2016, 09:58 PM
Post
#2
|
|
Custom Member Group: Members Posts: 24,645 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States
|
Very nice
Attached image(s) 
|
|
|
|
Posts in this topic
Olympic 1.7 Steering rack rebuild Jan 8 2016, 09:09 AM
DavidSweden
Thought I would install my Turbo tie rod ends and... Jan 8 2016, 10:52 AM Olympic 1.7 Ok I got the rack disassembled and found the end b... Jan 11 2016, 07:01 AM
DavidSweden
Ok I got the rack disassembled and found the end ... Jan 11 2016, 02:53 PM Olympic 1.7
The end bushing is probably ok, I left mine alon... Jan 11 2016, 04:08 PM jmill Good racks should be easy to find. I swapped mine... Jan 11 2016, 01:24 PM MikeM Contact Bruce Stone. I bought a really nice used o... Jan 11 2016, 04:20 PM r_towle Dunk the end with th bushing into kerosene for a f... Jan 11 2016, 05:40 PM Olympic 1.7 Sounds good, I'll give it a try..... Jan 11 2016, 07:02 PM Catorse I went down this road a month ago. None of the thr... Jan 11 2016, 07:56 PM Mikey914 Dude, what do you need?
I make the pucks for Stodd... Jan 12 2016, 12:15 PM r_towle
Dude, what do you need?
I make the pucks for Stod... Jan 12 2016, 02:36 PM Mikey914 Well I have the #7 cap, I'll look at the #19
I... Jan 12 2016, 02:38 PM r_towle
Well I have the #7 cap, I'll look at the #19
... Jan 13 2016, 08:44 AM Mikey914
Well I have the #7 cap, I'll look at the #19... Jan 14 2016, 01:29 AM Harpo That would be awesome if there was a kit with all ... Jan 13 2016, 12:28 PM r_towle Yes, exactly.
I believe it was called a short rack... Jan 14 2016, 07:36 PM Olympic 1.7 Well finished up the steering rack.
Turns out the... Feb 5 2016, 08:04 PM turnaround89 What is the little trick to removing the bearing a... Jan 7 2017, 07:47 PM Olympic 1.7
What is the little trick to removing the bearing ... Jan 9 2017, 08:09 AM Mikey914 Bearing puller. It's been pressed in. Jan 7 2017, 07:49 PM turnaround89 Thanks for the replies. I ended up buying a beat... Jan 9 2017, 12:23 PM Mikey914 One of the reasons I intend to do as a service. Jan 9 2017, 04:21 PM turnaround89 Mikey914 - Are you looking into making the bushing... Jan 9 2017, 06:06 PM Mikey914 I've already made the bushings on the other th... Jan 11 2017, 12:24 AM naro914 I wanted to revive this thread since I am trying t... Dec 29 2018, 11:50 AM bbrock I just did this last weekend. That bushing is the... Dec 29 2018, 12:52 PM naro914 Well...looks like it’s not going to work. The pi... Dec 29 2018, 01:46 PM Mikey914 We’ve found 4 different versions of the racks. C... Dec 29 2018, 09:37 PM Luke M
We’ve found 4 different versions of the racks. ... Jan 1 2019, 08:20 AM Mikey914 We do not sell the "kit" as we have foun... Jan 1 2019, 08:04 PM Mikey914 Here's what we did Jan 1 2019, 08:29 PM Mikey914 another
While not perfect still a great part Jan 1 2019, 08:31 PM Mikey914 another Jan 1 2019, 08:31 PM Mikey914 more Jan 1 2019, 08:32 PM Mikey914 We were dong another baked finish, but I like the ... Jan 1 2019, 08:34 PM |
12 User(s) are reading this topic (12 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 22nd November 2024 - 05:12 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.