 Remove transmission. |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Keith914 |
 Jul 15 2016, 01:24 PM
Post
#1
|
|
Member  Group: Members Posts: 248 Joined: 29-April 16 From: Laguna Beach, California 92651 Member No.: 19,948 Region Association: Southern California  |
Need to replace rear crankshaft oil seal. What is least amount of work: drop engine/transmission, or support engine in car and remove transmission?
|
   |
 
|
  |
Replies
| TheCabinetmaker |
Aug 2 2016, 01:23 PM
Post
#2
|
|
I drive my car everyday Group: Members Posts: 8,325 Joined: 8-May 03 From: Tulsa, Ok. Member No.: 666 |
Did you remove all four bolts or nuts from the bell housing? Never seen one not come loose
|
|
|
|
| mitche |
Aug 2 2016, 01:40 PM
Post
#3
|
|
Newbie Group: Members Posts: 6 Joined: 28-July 16 From: Sweden Member No.: 20,233 Region Association: None |
QUOTE(The Cabinetmaker @ Aug 2 2016, 01:23 PM)  Did you remove all four bolts or nuts from the bell housing? Never seen one not come loose Yes I did, but I think this engine has been under water or something similar... I bought it from Copart and they dont always give you the whole story... Bolts is away, starter is away - I can get a 5mm gap between bell housing and trans but thats all... Have gone crazy with WD40 and will wait and see... Thanks anyway mike |
|
|
|
Posts in this topic
Keith914 Remove transmission. Jul 15 2016, 01:24 PM
DavidSweden
Need to replace rear crankshaft oil seal. What is... Jul 15 2016, 01:42 PM SLITS Remove the tranny ....
The engine drop will addit... Jul 15 2016, 01:44 PM Keith914 Thanks for advice. Will leave engine in place and ... Jul 15 2016, 02:41 PM stugray just did this recently to rebuild my trans:
Jack ... Jul 15 2016, 03:20 PM
mitche
just did this recently to rebuild my trans:
Jack... Jul 29 2016, 02:48 PM stugray Try to actuate the clutch. The Throw out bearing w... Jul 30 2016, 12:51 AM mitche
Try to actuate the clutch. The Throw out bearing ... Aug 2 2016, 01:09 PM stugray
Did you remove all four bolts or nuts from the b... Aug 2 2016, 04:15 PM 76-914
[quote name='mitche' post='2379589' date='Aug 2 2... Aug 2 2016, 06:06 PM Reverend Troublemaker Except now he stated the engine is out of the car.... Aug 3 2016, 12:28 PM Jeffs9146 You could try to put it in 5th gear manually and t... Aug 3 2016, 01:15 PM mitche
You could try to put it in 5th gear manually and ... Aug 6 2016, 07:28 AM stugray
I can with a big hammer turn the flywheel so I ca... Aug 6 2016, 11:01 AM mitche
I can with a big hammer turn the flywheel so I c... Aug 6 2016, 11:16 AM mitche
[quote name='stugray' post='2381346' date='Aug 6 ... Aug 6 2016, 12:30 PM stugray
Well the bottom two bolts are studs (correct wor... Aug 6 2016, 01:19 PM 76-914 then absolutely :beer2: Aug 6 2016, 07:40 AM cuddyk Congrats! At this point you should be able to ... Aug 6 2016, 12:46 PM |
5 User(s) are reading this topic (5 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 6th January 2025 - 06:10 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.