 Remove transmission. |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Keith914 |
 Jul 15 2016, 01:24 PM
Post
#1
|
|
Member  Group: Members Posts: 248 Joined: 29-April 16 From: Laguna Beach, California 92651 Member No.: 19,948 Region Association: Southern California  |
Need to replace rear crankshaft oil seal. What is least amount of work: drop engine/transmission, or support engine in car and remove transmission?
|
   |
 
|
  |
Replies
| Jeffs9146 |
Aug 3 2016, 01:15 PM
Post
#2
|
|
Ski Bum Group: Members Posts: 4,062 Joined: 10-January 03 From: Discovery Bay, Ca Member No.: 128 |
You could try to put it in 5th gear manually and turn the output shafts while pulling the trans away from the engine.
|
|
|
|
| mitche |
Aug 6 2016, 07:28 AM
Post
#3
|
|
Newbie Group: Members Posts: 6 Joined: 28-July 16 From: Sweden Member No.: 20,233 Region Association: None |
QUOTE(Jeffs9146 @ Aug 3 2016, 01:15 PM)  You could try to put it in 5th gear manually and turn the output shafts while pulling the trans away from the engine. Update: When I put in any gear the driveshafts just turns around just like there is no gear in place. This makes me believe that the clutch is corroded in "engaged" position, correct assumption? I can with a big hammer turn the flywheel so I can reach every 13mm nut through the starter hole. Should I remove these 13 mm nuts? Cheers Mike BTW here's the beauty...  |
|
|
|
Posts in this topic
Keith914 Remove transmission. Jul 15 2016, 01:24 PM
DavidSweden
Need to replace rear crankshaft oil seal. What is... Jul 15 2016, 01:42 PM SLITS Remove the tranny ....
The engine drop will addit... Jul 15 2016, 01:44 PM Keith914 Thanks for advice. Will leave engine in place and ... Jul 15 2016, 02:41 PM stugray just did this recently to rebuild my trans:
Jack ... Jul 15 2016, 03:20 PM
mitche
just did this recently to rebuild my trans:
Jack... Jul 29 2016, 02:48 PM stugray Try to actuate the clutch. The Throw out bearing w... Jul 30 2016, 12:51 AM mitche
Try to actuate the clutch. The Throw out bearing ... Aug 2 2016, 01:09 PM The Cabinetmaker Did you remove all four bolts or nuts from the bel... Aug 2 2016, 01:23 PM mitche
Did you remove all four bolts or nuts from the be... Aug 2 2016, 01:40 PM stugray
Did you remove all four bolts or nuts from the b... Aug 2 2016, 04:15 PM 76-914
[quote name='mitche' post='2379589' date='Aug 2 2... Aug 2 2016, 06:06 PM Reverend Troublemaker Except now he stated the engine is out of the car.... Aug 3 2016, 12:28 PM stugray
I can with a big hammer turn the flywheel so I ca... Aug 6 2016, 11:01 AM mitche
I can with a big hammer turn the flywheel so I c... Aug 6 2016, 11:16 AM mitche
[quote name='stugray' post='2381346' date='Aug 6 ... Aug 6 2016, 12:30 PM stugray
Well the bottom two bolts are studs (correct wor... Aug 6 2016, 01:19 PM 76-914 then absolutely :beer2: Aug 6 2016, 07:40 AM cuddyk Congrats! At this point you should be able to ... Aug 6 2016, 12:46 PM |
6 User(s) are reading this topic (6 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 6th January 2025 - 06:24 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.