 1970 914/6 Harness Horror, Main Wiring Harness Connection |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Howie149 |
 Aug 10 2016, 08:42 PM
Post
#1
|
|
Newbie  Group: Members Posts: 4 Joined: 10-August 16 From: Emerald Hills, CA Member No.: 20,286 Region Association: None  |
I have a 1970 914/6. When I pulled the motor out, the 14 pin Main Harness that sits on the Relay Board in the engine compartment came apart. Thus I have no idea which wire goes where. I have 6 wires. (2 are grey and black and go to the transmission back-up switch/sender. 1 Green and brown and 1 Green and black go to the oil pressure and oil level senders. 1 Black and red goes to the coil and I'm not sure about the black and blue/purple.) I have attached a picture of the harness below.
I would enjoy any guidance on where to plug these wires. Car won't start and it keeps blowing fuses which I assume is either a problem with these wires or the ignition system/distributor needs an overhaul. Attached thumbnail(s) 
|
   |
 
|
  |
Replies
| cary |
Aug 10 2016, 09:06 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 3,900 Joined: 26-January 04 From: Sherwood Oregon Member No.: 1,608 Region Association: Pacific Northwest 
|
Your fired ...
You need to give the car to me .... LOL All kidding aside. No big deal. If you look closely at the black connector it should have little numbers. The schematic will have matching numbers. Just plug them back in the correct hole. I'm stripping down another 964 at work. While removing the 40# harness. One of the 6 pin versions behind the gauges came apart. I got lucky. It didn't explode like yours. |
|
|
|
Posts in this topic
Howie149 1970 914/6 Harness Horror Aug 10 2016, 08:42 PM
Howie149
Your fired ...
You need to give the car to me ...... Aug 10 2016, 09:39 PM porschetub
[quote name='cary' post='2383467... Aug 10 2016, 10:45 PM
cary My manuals are at my shop.
I won't be out ther... Aug 10 2016, 09:41 PM Peashooter
I have a 1970 914/6. When I pulled the motor out... Aug 11 2016, 05:42 AM porschetub
I have a 1970 914/6. When I pulled the motor ou... Aug 11 2016, 01:12 PM rgalla9146 I took a picture of the multi-pin connectors with ... Aug 11 2016, 08:05 AM JmuRiz
Why do you have a tach adapter ?
I was thinkin... Aug 11 2016, 08:24 AM rgalla9146 Most likely a real 6, the oil line to the tank has... Aug 11 2016, 10:39 AM Dion
Why do you have a tach adapter ?
I was thinki... Aug 11 2016, 10:44 AM Dave_Darling If the wiring follows the same convention as the f... Aug 11 2016, 12:22 PM ClayPerrine
If the wiring follows the same convention as the ... Aug 11 2016, 08:56 PM Howie149 Its a numbers matching car but the wiring harness ... Aug 11 2016, 07:57 PM Perry Kiehl Clone Looks like it could be one of my harnesses, or may... Aug 11 2016, 08:16 PM porschetub
Looks like it could be one of my harnesses, or ma... Aug 11 2016, 10:24 PM Howie149
Looks like it could be one of my harnesses, or ma... Aug 12 2016, 12:14 AM sixnotfour :beer1: Aug 11 2016, 09:25 PM SixerJ Positive you have a six board, two vertical plugs ... Aug 12 2016, 12:43 AM |
10 User(s) are reading this topic (10 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 22nd December 2024 - 11:50 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.