 Bought my 914 need help., Need help |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Ncchany |
 Oct 1 2016, 12:38 PM
Post
#1
|
|
Newbie  Group: Members Posts: 36 Joined: 1-October 16 From: New york Member No.: 20,456 Region Association: None  |
Alright guys i just bought a 914. I am so excited!!! Its a big project so i am going to need your guys help and guidance. Okay for starters the shifter seems loose and the ebrake isnt working? Were do i start with that so i dont have to use chalks
|
   |
 
|
  |
Replies
| rhodyguy |
Oct 1 2016, 05:48 PM
Post
#2
|
|
Chimp Sanctuary NW. Check it out. Group: Members Posts: 22,198 Joined: 2-March 03 From: Orion's Bell. The BELL! Member No.: 378 Region Association: Galt's Gulch |
Get and read the book. Do ONE task at a time! Does the car run? Before you start throwing handfuls of money at the car, take LOTS of pictures and post them in this thread showing what you consider the worst/most suspect areas. These folks with their eagle eyes will point things out you may not even notice. The good people here will help guide you on your journey.
|
|
|
|
Posts in this topic
Ncchany Bought my 914 need help. Oct 1 2016, 12:38 PM
Ncchany
Alright guys i just bought a 914. I am so excited... Oct 1 2016, 12:43 PM zipedadoo There are cables that runs from the handle to both... Oct 1 2016, 12:53 PM ClayPerrine I would suggest your first purchase be a Haynes Ma... Oct 1 2016, 12:57 PM
Ncchany Its a 1974 914 1.8l
Also its missing the handbrak... Oct 1 2016, 01:14 PM
396
I would suggest your first purchase be a Haynes M... Oct 1 2016, 03:36 PM ClayPerrine The handbrake lever should be between the driver... Oct 1 2016, 01:19 PM Ncchany What do you guys think of this? I need help with t... Oct 1 2016, 01:22 PM Mblizzard Plan on replacing allow the shifter bushings. Ins... Oct 1 2016, 01:28 PM Shadowfax :wttc: Oct 1 2016, 01:59 PM McMark Yup, replace all the shifter bushings. All of the... Oct 1 2016, 03:16 PM Ncchany The ebrake is rock solid and wont go up. Where can... Oct 1 2016, 03:23 PM Ncchany
The ebrake is rock solid and wont go up. Where ca... Oct 1 2016, 03:24 PM cwpeden
[quote name='Ncchany' post='2405743' date='Oct 1 ... Oct 1 2016, 03:52 PM Mblizzard The sources for the bushings are plentiful. But I ... Oct 1 2016, 03:49 PM injunmort as mentioned, remove cable ends from calipers. if ... Oct 1 2016, 03:56 PM RobW :wttc: :wttc: :wttc: Oct 1 2016, 04:25 PM Ncchany
:wttc: :wttc: :wttc:
Thanks to everyone for... Oct 1 2016, 05:07 PM Dave_Darling Here is some reading material, with photos, about ... Oct 1 2016, 05:08 PM euro911 That sure brings back some memories.
http://www.9... Oct 1 2016, 05:25 PM Ncchany
That sure brings back some memories.
http://www.... Oct 1 2016, 06:13 PM euro911 [quote name='euro911' post='2405811' date='Oct 1 2... Oct 1 2016, 07:29 PM Ncchany
Get and read the book. Do ONE task at a time... Oct 1 2016, 06:43 PM Mikey914 Dude buy the bushings from me and I'll throw ... Oct 1 2016, 08:40 PM Ncchany
Dude buy the bushings from me and I'll throw... Oct 2 2016, 01:23 PM rhodyguy What's your take on the most important thing t... Oct 2 2016, 01:53 PM McMark Seek out and eliminate structural rust first.
Get ... Oct 2 2016, 01:55 PM rhodyguy If the pass side front is an indication of mark... Oct 2 2016, 02:00 PM |
14 User(s) are reading this topic (14 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 5th January 2025 - 01:45 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.