 Floor Pan Coating? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| dgraves |
  Oct 15 2016, 09:50 AM
Post
#1
|
|
1974 914 2.0  Group: Members Posts: 180 Joined: 6-June 16 From: Montana Member No.: 20,076 Region Association: Rocky Mountains  |
As I continue the refurbishment of my '74 914, I notice that the floor pan inside the car has some kind of a 3/16" protective coating. Parts of this have chipped away. Does anyone have a substitute application to patch and restore the floor pan?
|
   |
 
|
  |
Replies
| slotty008 |
Oct 15 2016, 01:28 PM
Post
#2
|
|
Member Group: Members Posts: 192 Joined: 11-November 15 From: Belgium Member No.: 19,349 Region Association: None 
|
It's a pain to remove the tar coating . But I think you really should do it , because the rust gets underneath. I'm in the course of doing it right now; takes a lot of time. Afterwards I'm gonna put 2 coats of zinc paint on the metal and then a layer of Dynamat.
|
|
|
|
Posts in this topic
dgraves Floor Pan Coating? Oct 15 2016, 09:50 AM
Mikey914 It's basically a tar pad. They are known to ha... Oct 15 2016, 10:54 AM
dgraves Thank you. Luckily, the car is pretty rust free a... Oct 15 2016, 11:54 AM BeatNavy
Do you know what was used in the areas where the ... Oct 15 2016, 12:07 PM jcd914
It appears that it was applied[b] right over the... Oct 15 2016, 12:37 PM Mikey914 If you really want to protect it, I'd have it ... Oct 15 2016, 12:12 PM ndfrigi you may see like these under tar.
Oct 15 2016, 02:24 PM ndfrigi RE: Floor Pan Coating? Oct 15 2016, 02:25 PM Mr.Nobody What are people's thoughts on the best way to ... Oct 15 2016, 05:06 PM matthepcat Heat gun and large screw driver or chisel worked f... Oct 15 2016, 05:22 PM stevegm
Heat gun and large screw driver or chisel worked ... Oct 15 2016, 05:47 PM bandjoey $39 multi tool at Harbor Freight. It cuts the... Oct 15 2016, 10:52 PM draganc
$39 multi tool at Harbor Freight. It cuts th... Oct 16 2016, 07:19 PM cary My .02c.
Heat gun and multi-tool or air chisel. Yo... Oct 16 2016, 06:54 AM mepstein
My .02c.
Heat gun and multi-tool or air chisel. Y... Oct 16 2016, 07:33 AM cary I plan to try that on the next race car strip down... Oct 16 2016, 07:48 AM 74ravenna I hate to ask but does anyone know what the ... Oct 16 2016, 08:08 AM 74ravenna Did porsche use this method of coating on the 911s... Oct 16 2016, 10:59 AM cary
Did porsche use this method of coating on the 911... Oct 16 2016, 07:44 PM rmdinmd As long as the fibers don't float in the air y... Oct 16 2016, 05:22 PM tomeric914 If you don't want to to use an adhesive backed... Oct 16 2016, 05:35 PM dgraves Spectrum? Ok, I'll look into it. The tar has... Oct 16 2016, 05:42 PM 74ravenna
Spectrum? Ok, I'll look into it. The tar ha... Oct 16 2016, 07:18 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 19th April 2025 - 01:07 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.