 Engine Build Recommendadtion |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| N_Jay |
 Oct 29 2016, 11:03 AM
Post
#1
|
|
Member  Group: Members Posts: 283 Joined: 2-March 16 From: Chicago NW Burbs Member No.: 19,720 Region Association: None  |
OK, we have recently hashed out head gaskets, Pistons, rods, and bearings.
A while a go it was oil pumps. So what about a fresh build discussion. I plan on building a decent 2.0 based street engine. Goals are decent power, longevity and drivability. Think fun reliable touring with an occasional autocross. (Kind of what a factory 2.0 was good for, but with a little more kick in the pants.) AND reasonable price (Yes, that is always open to interpretation) What is recommended displacement? Bore and Stroke? What pistons, rods and cylinders? What compression? What cam? Guessing micro squirt or tuned up D-Jet. What "tricks" are worth while for a few HP and/or drivability, longevity, etc. What "tricks" are not worth while (or worst yet help one direction and hurt another) How much worse would it be to start with a 1.8 base? (Heads, etc.) |
   |
 
|
  |
Replies
| Larmo63 |
Oct 29 2016, 09:52 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 4,267 Joined: 3-March 14 From: San Clemente, Ca Member No.: 17,068 Region Association: Southern California |
I'd have McMark build your engine if you are up in that part of the country...
|
|
|
|
Posts in this topic
N_Jay Engine Build Recommendadtion Oct 29 2016, 11:03 AM
tomh light flywheel is always an easy not too expensive... Oct 29 2016, 11:50 AM
stugray
light flywheel is always an easy not too expensiv... Oct 29 2016, 12:00 PM tomh
light flywheel is always an easy not too expensi... Oct 29 2016, 07:18 PM porschetub
light flywheel is always an easy not too expensi... Oct 31 2016, 01:40 AM stevegm Oil pump is not quite resolved yet. The stock pump... Oct 29 2016, 04:49 PM stugray Quick Recipe:
96mm jugs & KB pistons from Euro... Oct 29 2016, 05:06 PM euro911 Quick Recipe:
96mm jugs & KB pistons from Euro... Oct 31 2016, 02:50 AM N_Jay
Quick Recipe:
96mm jugs & KB pistons from Eur... Oct 31 2016, 07:45 AM injunmort you gotta have a set of HAM,INC heads otherwise it... Oct 29 2016, 06:12 PM HAM Inc LN Engineering/Type4Store sells complete, high qua... Oct 30 2016, 08:40 AM ConeDodger 2056. Enjoyable, still driveable. Yes, the LE seri... Oct 29 2016, 07:22 PM cwpeden
2056. Enjoyable, still driveable. Yes, the LE ser... Oct 29 2016, 08:13 PM ClayPerrine My engine recipe:
Stock 2.0 crank
Stock 2.0 rod... Oct 30 2016, 07:16 AM stugray
you gotta have a set of HAM,INC heads otherwise i... Oct 30 2016, 11:59 AM tomh
you gotta have a set of HAM,INC heads otherwise ... Oct 30 2016, 12:01 PM N_Jay OK, I am not looking for someone to build it.
Pro... Oct 30 2016, 05:02 PM Dave_Darling
2056 is 96mm on a stock crank?
96mm bore, 71mm s... Oct 30 2016, 05:52 PM Mark Henry
I noticed that et HAM heads are 4 stud (1.8 styl... Oct 31 2016, 12:07 AM N_Jay Thank so far.
More questions will be coming, but ... Oct 30 2016, 07:02 PM cgnj
Thank so far.
More questions will be coming, but... Oct 30 2016, 09:11 PM N_Jay
Lots of stuff to start with. Do you have inducti... Oct 31 2016, 07:39 AM euro911 As was mentioned above, you can also check with Ge... Oct 31 2016, 12:28 PM davep What are the current recommendations on bearings? ... Jan 18 2017, 07:04 AM euro911 Dave, call George at European (310) 644-8038 ... h... Jan 18 2017, 01:48 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 31st October 2024 - 07:22 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.