 Clutch arm position ?, correct or not... |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| porschetub |
 Oct 1 2017, 04:55 PM
Post
#1
|
|
Advanced Member  Group: Members Posts: 4,756 Joined: 25-July 15 From: New Zealand Member No.: 18,995 Region Association: None  |
Based on what I have studied I seem to think this is not right,new pressure plate/disk,new cable,rebuilt pedal assembly etc ,etc and unknown flywheel in good condition,thinking it has been heavily machined,pedal adjustment is by the book...my idea is the lever is hitting the trans case when pedal fully down...help please before I pull the g/box again.
 TIA guys. P.S.clutch cable tube is fine. |
   |
 
|
  |
Replies
| rhodyguy |
Oct 1 2017, 09:31 PM
Post
#2
|
|
Chimp Sanctuary NW. Check it out. Group: Members Posts: 22,195 Joined: 2-March 03 From: Orion's Bell. The BELL! Member No.: 378 Region Association: Galt's Gulch |
Put some washers under the cable nut. If that's a nyloc nut on the cable you might want to back it Up with a jam nut.
|
|
|
|
Posts in this topic
porschetub Clutch arm position ? Oct 1 2017, 04:55 PM
mobymutt Mine was doing the same thing -- I adjusted the cl... Oct 1 2017, 05:19 PM
ndfrigi
Mine was doing the same thing -- I adjusted the c... Oct 1 2017, 05:44 PM Larmo63 I think he meant the silver nut at the edge of the... Oct 1 2017, 05:59 PM mobymutt I did, but I suspect it's just the back end of... Oct 1 2017, 06:31 PM r_towle You can shim the clutch release fork pivot ball to... Oct 1 2017, 06:37 PM porschetub
You can shim the clutch release fork pivot ball t... Oct 1 2017, 09:00 PM ndfrigi
You can shim the clutch release fork pivot ball ... Oct 1 2017, 09:24 PM porschetub
[quote name='porschetub' post='2533397' date='Oct... Oct 1 2017, 10:01 PM mgphoto Adding washers or extending anything to compensate... Oct 2 2017, 03:53 PM porschetub
Adding washers or extending anything to compensat... Oct 2 2017, 05:31 PM r_towle Cut a board to fit sideways in front of the seat t... Oct 2 2017, 06:24 PM porschetub
Cut a board to fit sideways in front of the seat ... Oct 2 2017, 10:37 PM Lucky9146
[quote name='r_towle' post='2533670' date='Oct 3 ... Oct 2 2017, 11:03 PM porschetub
[quote name='r_towle' post='2533670' date='Oct 3... Oct 3 2017, 12:01 PM mark04usa Clearance is an issue. I use a 1/4" drive dee... Oct 2 2017, 11:07 PM porschetub Mongreled a thin wall cheapo $1 socket ,bored... Oct 3 2017, 06:03 PM r_towle Measure the flywheel to see how much was ground of... Oct 3 2017, 10:17 PM porschetub
Measure the flywheel to see how much was ground o... Oct 4 2017, 03:45 AM Dr Evil Im at work so don't have diagram here, unfortu... Oct 4 2017, 11:01 AM porschetub
Im at work so don't have diagram here, unfort... Oct 4 2017, 12:41 PM johnhora here you go...flywheel specs
Oct 4 2017, 02:44 PM Dave_Darling
here you go...flywheel specs
Notice the upper-r... Oct 6 2017, 02:34 PM porschetub
here you go...flywheel specs
Notice the upper-... Oct 7 2017, 01:17 PM Dr Evil Rock on! I just got home....so no need to do t... Oct 4 2017, 03:39 PM porschetub Thanks guys ,getting ready to refit box,will pull ... Oct 4 2017, 03:51 PM porschetub Ok got the clutch out,all in order,my digital vern... Oct 4 2017, 04:08 PM johnhora porschetub...
also check the fork....there is a l... Oct 4 2017, 07:03 PM porschetub
porschetub...
also check the fork....there is a ... Oct 4 2017, 11:30 PM r_towle Broken spring in pressure plate is hard to test.
S... Oct 5 2017, 04:01 PM porschetub
Broken spring in pressure plate is hard to test.
... Oct 6 2017, 01:45 AM |
10 User(s) are reading this topic (10 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 28th December 2024 - 02:33 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.