 Misc /6 stuff..., Bushings available? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Lawrence |
 May 19 2003, 07:38 AM
Post
#1
|
|
Senior Member  Group: Benefactors Posts: 1,661 Joined: 5-February 03 Member No.: 244 Region Association: None   |
I replaced the speedo cable, and had time to look at some other stuff. The replacement didn't work out as easily as I planned - mostly because the old cable was misrouted by the DPO. So, I did remove most of the interior.
While I was under the car, I removed and cleaned the angle drive. This one appeared to be original, so I'm planning on getting another to have on hand. The angle drive screws into an aluminum part (cylinder shaped, that my catalog calls a "boot") that goes into the transmission housing to hold the speedo drive shaft in place. I have a small leak coming from there (probably the o-ring or seal ring inside). The boot should be held in place by a setscrew and threaded insert. My concern is that the setscrew and insert are very tight - but this aluminum piece has a small wiggle to it. Do I have a problem? Also, on the accelerator linkage, at the two bell cranks, I appear to be missing bushings. Does anyone know if these are available? Stoddard's printed catalog carries them as NLA. -Rusty |
   |
 
|
  |
Replies
| Brad Roberts |
May 19 2003, 08:13 AM
Post
#2
|
|
914 Freak! Group: Members Posts: 19,148 Joined: 23-December 02 Member No.: 8 Region Association: None |
I'm not quite sure why Charlie cant post it here... I know he is not putting it on this year "per se" but.. there is no reason not to access this group of 700 some odd people.
B |
|
|
|
Posts in this topic
Lawrence914-6 Misc /6 stuff... May 19 2003, 07:38 AM
Gint You talking about the bushings at the manifold bel... May 19 2003, 07:43 AM Brad Roberts I just bought bushings from HPH for the blue6.. he... May 19 2003, 07:48 AM Lawrence914-6 Yeah, that bellcrank and the one at the transmissi... May 19 2003, 07:48 AM Brad Roberts He has a new parts guy named Rick.. super nice guy... May 19 2003, 07:51 AM Lawrence914-6 So am I looking at replacing the end cover?
Hey B... May 19 2003, 07:51 AM Brad Roberts I know he has the bronze bushings in stock... and ... May 19 2003, 07:52 AM Lawrence914-6 I'm cheap, but even I fail to see the economy ... May 19 2003, 07:59 AM Brad Roberts Rich would only keep good used ones..
I dont rec... May 19 2003, 08:02 AM Lawrence914-6 Will do.
Did you get my mail about the door? May 19 2003, 08:06 AM Brad Roberts I havent checked email in almost 4 days....so NO I... May 19 2003, 08:09 AM Lawrence914-6 Quit being so lazy, and get your mail. ;-)
-Rust... May 19 2003, 08:11 AM Brad Roberts Can you PLEASE post the MUSR here ?? I need dates/... May 19 2003, 08:12 AM
Lawrence914-6 I'll get on it. May 19 2003, 08:24 AM |
4 User(s) are reading this topic (4 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 22nd December 2024 - 04:21 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.